Home

The WetroomStop Linear Clamp Tray 900 x 1850 mm, available in 3 thicknesses, is a is a wet room tray for vinyl floors. It comes with an integrated drain that has a clamping mechanism which allows it to secure the edges of the vinyl sheet around the drain.

The tray is made of XPS foam, which is lightweight but durable and offers insulation properties. It is reinforced with fibreglass mesh and cement based glue from both sides. It also has a waterproof membrane on the top side for added protection.The tray can also be trimmed down if required to fit a specific dimension.

The tray comes as a complete set, with a brushed stainless steel cover that is available in a variety of styles. A McAlpine HC26-50 waste trap with 1.5’’ size outlet, and the optional WetroomStop Waterproofing Kit.

This WetroomStop Linear Clamp Tray 900 x 1850 mm tray is the longest in our store. It is great for larger rooms that require a lot of the floor area to be sloped. It gives you the peace of mind that all water from the shower will find its way back to the drain. The gentle slope provides efficient drainage without making the floor feel or look slanted.

Our most popular size tray, but this one offers the drain along the 1500mm side of the tray. The drain is 600mm long and is located 150mm from the edge. This is a great option for a shower that is wider than it is longer. Our Wet Room Shower Trays with Linear drains for tiled floors are the most versatile shower former you will find. They come with an integrated 600mm linear drain and are available in various sizes with different drain positions.

Each Tray's Advanced 3 piece drain offers plenty of flexibility and safety as well. The integrated plastic channel is factory installed into the tray assuring a water tight seal and allowing for the waste trap to be connected anywhere along the channel. The 304 grade stainless steel frame and cover make up the remaining parts of the drain. They are available in a variety of PVD coated colours and finishes. The frame is height adjustable to match the finished floor height. It also offers secondary drainage in case water were to ever penetrate the floor covering it will find its way to the drain. The cover itself is reversible, allowing you to either leave it right side up for a stainless steel finish to the cover or flipping it over and tiling inside for a tiled finish.

These XPS foam Trays have a 4 way slope machine cut into with an estimated 1-2% gradient fall. The bottom side of the tray is level and the integrated channel does not protrude below the tray allowing for both timber and concrete floor installation. Furthermore the hole (hole cutter provided) for the waste trap is drilled on site by the installer making avoiding joists that much simpler. Although the tray provides great thermal and acoustic insulation it is not structural so it will require to be supported throughout its entirety. The Trays are trim-able and can be cut down to a specific size or to avoid corners or match uneven walls or irregular angles.

The Microcement Linear shower drain series is meticulously engineered for compatibility with microcement, resin, and similar floor coverings. Featuring an adjustable frame and drain cover offering adjustment from 3 to 12 mm, it accommodates a wide range of materials seamlessly. Available in various variants, the drain suits a variety of shower sizes and designs. Equipped with a secondary drainage system, it efficiently drains water seeping through the surface finish to the insulation layer. Additional features include multiple fittings colours, painted using the PVD method, ensuring durability and longevity. Choose from brushed, polished, or matte finishing options for the drain surface, along with seven available drain cover styles to suit your aesthetic preferences. Each supplied set includes a waste trap, sealing membrane, and adjustable legs. Select the ideal waste trap based on flow rate requirements and available space, while the sealing membrane ensures waterproofing of the joint between the floor and drain. The optional detachable legs facilitate easy installation on concrete floors by levelling the drain. As a standard product in our range, we prioritise stocking with off-the-shelf dispatch availability and next-day delivery. With multiple sizes and style variants available, finding the perfect drain for microcement applications is effortless, ensuring efficient delivery and exceptional product quality.

All our PVD coated linear drains are crafted from premium 304 grade stainless steel, ensuring durability and longevity. Each drain comprises three essential components: the drain body, adjustable frame, and reversible cover. With your purchase, you receive stainless steel adjustable legs, a pre-glued waterproof membrane, and the option to select your preferred waste trap. The reversible cover offers versatility, allowing you to opt for either a smooth steel finish or flip the cover to tile inside the insert for a fully tiled appearance in your wet room. Furthermore, the height of the drain is adjustable, providing a range from 8mm to 12mm, depending on the thickness of the tiles you intend to install.

The WetroomStop Linear Clamp Tray 900 x 1850 mm, available in 3 thicknesses, is a is a wet room tray for vinyl floors. It comes with an integrated drain that has a clamping mechanism which allows it to secure the edges of the vinyl sheet around the drain.

The tray is made of XPS foam, which is lightweight but durable and offers insulation properties. It is reinforced with fibreglass mesh and cement based glue from both sides. It also has a waterproof membrane on the top side for added protection.The tray can also be trimmed down if required to fit a specific dimension.

The tray comes as a complete set, with a brushed stainless steel cover that is available in a variety of styles. A McAlpine HC26-50 waste trap with 1.5’’ size outlet, and the optional WetroomStop Waterproofing Kit.

This WetroomStop Linear Clamp Tray 900 x 1850 mm tray is the longest in our store. It is great for larger rooms that require a lot of the floor area to be sloped. It gives you the peace of mind that all water from the shower will find its way back to the drain. The gentle slope provides efficient drainage without making the floor feel or look slanted.

Our most popular size tray, but this one offers the drain along the 1200mm side of the tray. The drain is 600mm long and is located 150mm from the edge. This is a great option for a shower that is wider than it is longer. Our Wet Room Shower Trays with Linear drains for tiled floors are the most versatile shower former you will find. They come with an integrated 600mm linear drain and are available in various sizes with different drain positions.

Each Tray's Advanced 3 piece drain offers plenty of flexibility and safety as well. The integrated plastic channel is factory installed into the tray assuring a water tight seal and allowing for the waste trap to be connected anywhere along the channel. The 304 grade stainless steel frame and cover make up the remaining parts of the drain. They are available in a variety of PVD coated colours and finishes. The frame is height adjustable to match the finished floor height. It also offers secondary drainage in case water were to ever penetrate the floor covering it will find its way to the drain. The cover itself is reversible, allowing you to either leave it right side up for a stainless steel finish to the cover or flipping it over and tiling inside for a tiled finish.

These XPS foam Trays have a 4 way slope machine cut into with an estimated 1-2% gradient fall. The bottom side of the tray is level and the integrated channel does not protrude below the tray allowing for both timber and concrete floor installation. Furthermore the hole (hole cutter provided) for the waste trap is drilled on site by the installer making avoiding joists that much simpler. Although the tray provides great thermal and acoustic insulation it is not structural so it will require to be supported throughout its entirety. The Trays are trim-able and can be cut down to a specific size or to avoid corners or match uneven walls or irregular angles.

All our PVD coated linear drains are crafted from premium 304 grade stainless steel, ensuring durability and longevity. Each drain comprises three essential components: the drain body, adjustable frame, and reversible cover. With your purchase, you receive stainless steel adjustable legs, a pre-glued waterproof membrane, and the option to select your preferred waste trap. The reversible cover offers versatility, allowing you to opt for either a smooth steel finish or flip the cover to tile inside the insert for a fully tiled appearance in your wet room. Furthermore, the height of the drain is adjustable, providing a range from 8mm to 12mm, depending on the thickness of the tiles you intend to install.

The WetroomStop Linear Clamp Tray 900 x 900 mm, available in 3 thicknesses, is a is a wet room tray for vinyl floors. It comes with an integrated clamp drain that mechanically secures the edges of the vinyl sheet around the drain.

The tray is made of XPS foam, which is lightweight but durable and offers insulation properties. It is reinforced with fibreglass mesh and cement based glue from both sides. It also has a waterproof membrane on the top side for added protection.The tray can also be trimmed down if required to fit a specific dimension.

The tray comes as a complete set, with a brushed stainless steel cover that is available in a variety of styles. A McAlpine HC26-50 waste trap with 1.5’’ size outlet, and the optional WetroomStop Waterproofing Kit.

This WetroomStop Linear Clamp Tray 900 x 900 mm is the second smallest standard wet room tray available for vinyl flooring. Its compact size is close to one metre square. The small size of the tray helps the water in shower area to find its way to the drain faster as the slope is steeper. This is an optimal wet room tray for creating a spacious shower in a restricted space.

Our most popular size tray, but this one offers the drain along the 1500mm side of the tray. The drain is 600mm long and is located 150mm from the edge. This is a great option for a shower that is wider than it is longer. Our Wet Room Shower Trays with Linear drains for tiled floors are the most versatile shower former you will find. They come with an integrated 600mm linear drain and are available in various sizes with different drain positions.

Each Tray's Advanced 3 piece drain offers plenty of flexibility and safety as well. The integrated plastic channel is factory installed into the tray assuring a water tight seal and allowing for the waste trap to be connected anywhere along the channel. The 304 grade stainless steel frame and cover make up the remaining parts of the drain. They are available in a variety of PVD coated colours and finishes. The frame is height adjustable to match the finished floor height. It also offers secondary drainage in case water were to ever penetrate the floor covering it will find its way to the drain. The cover itself is reversible, allowing you to either leave it right side up for a stainless steel finish to the cover or flipping it over and tiling inside for a tiled finish.

These XPS foam Trays have a 4 way slope machine cut into with an estimated 1-2% gradient fall. The bottom side of the tray is level and the integrated channel does not protrude below the tray allowing for both timber and concrete floor installation. Furthermore the hole (hole cutter provided) for the waste trap is drilled on site by the installer making avoiding joists that much simpler. Although the tray provides great thermal and acoustic insulation it is not structural so it will require to be supported throughout its entirety. The Trays are trim-able and can be cut down to a specific size or to avoid corners or match uneven walls or irregular angles.

The WetroomStop Linear Clamp Tray 900 x 900 mm, available in 3 thicknesses, is a is a wet room tray for vinyl floors. It comes with an integrated clamp drain that mechanically secures the edges of the vinyl sheet around the drain.

The tray is made of XPS foam, which is lightweight but durable and offers insulation properties. It is reinforced with fibreglass mesh and cement based glue from both sides. It also has a waterproof membrane on the top side for added protection.The tray can also be trimmed down if required to fit a specific dimension.

The tray comes as a complete set, with a brushed stainless steel cover that is available in a variety of styles. A McAlpine HC26-50 waste trap with 1.5’’ size outlet, and the optional WetroomStop Waterproofing Kit.

This WetroomStop Linear Clamp Tray 900 x 900 mm is the second smallest standard wet room tray available for vinyl flooring. Its compact size is close to one metre square. The small size of the tray helps the water in shower area to find its way to the drain faster as the slope is steeper. This is an optimal wet room tray for creating a spacious shower in a restricted space.

Our most popular size tray, but this one offers the drain along the 1400mm side of the tray. The drain is 600mm long and is located 150mm from the edge. This is a great option for a shower that is wider than it is longer. Our Wet Room Shower Trays with Linear drains for tiled floors are the most versatile shower former you will find. They come with an integrated 600mm linear drain and are available in various sizes with different drain positions.

Each Tray's Advanced 3 piece drain offers plenty of flexibility and safety as well. The integrated plastic channel is factory installed into the tray assuring a water tight seal and allowing for the waste trap to be connected anywhere along the channel. The 304 grade stainless steel frame and cover make up the remaining parts of the drain. They are available in a variety of PVD coated colours and finishes. The frame is height adjustable to match the finished floor height. It also offers secondary drainage in case water were to ever penetrate the floor covering it will find its way to the drain. The cover itself is reversible, allowing you to either leave it right side up for a stainless steel finish to the cover or flipping it over and tiling inside for a tiled finish.

These XPS foam Trays have a 4 way slope machine cut into with an estimated 1-2% gradient fall. The bottom side of the tray is level and the integrated channel does not protrude below the tray allowing for both timber and concrete floor installation. Furthermore the hole (hole cutter provided) for the waste trap is drilled on site by the installer making avoiding joists that much simpler. Although the tray provides great thermal and acoustic insulation it is not structural so it will require to be supported throughout its entirety. The Trays are trim-able and can be cut down to a specific size or to avoid corners or match uneven walls or irregular angles.

Experience Seamless Luxury with Our Microcement-Ready WetroomStop Side Shower Tray:

Crafted at a substantial 40mm thickness, our shower base ensures a smooth, level-access transition into your shower space, eliminating the need for cumbersome steps. Engineered with XPS foam and reinforced with fibreglass mesh on both sides, our tray boasts unparalleled strength and durability. Its flexible cement coating, specially hardened for microcement application, guarantees a flawless surface for your desired finish.

Our tray's innovative 3-piece drain system offers both versatility and safety. The factory-installed steel drain ensures a watertight seal, while the 304 grade stainless steel frame and cover provide enduring quality. With a range of PVD coated colours and finishes available, you can customise your drain to match your aesthetic preferences. Plus, the height-adjustable frame accommodates various floor heights, as well as secondary drainage functionality.

Designed for precision, our trays feature a 4-way slope machine cut with a subtle 1-2% fall, ensuring efficient water drainage. The integrated channel sits flush with the tray's bottom surface, allowing for seamless microcement floor installation. And for ultimate customization, our trimmable trays can be effortlessly adjusted to fit specific dimensions, accommodate irregular angles, or match uneven walls.

Elevate your shower experience with our Microcement-Ready WetroomStop Shower Tray Collection – where functionality meets sophistication.

The WetroomStop Linear Clamp Tray 900 x 900 mm, available in 3 thicknesses, is a is a wet room tray for vinyl floors. It comes with an integrated clamp drain that mechanically secures the edges of the vinyl sheet around the drain.

The tray is made of XPS foam, which is lightweight but durable and offers insulation properties. It is reinforced with fibreglass mesh and cement based glue from both sides. It also has a waterproof membrane on the top side for added protection.The tray can also be trimmed down if required to fit a specific dimension.

The tray comes as a complete set, with a brushed stainless steel cover that is available in a variety of styles. A McAlpine HC26-50 waste trap with 1.5’’ size outlet, and the optional WetroomStop Waterproofing Kit.

This WetroomStop Linear Clamp Tray 900 x 900 mm is the second smallest standard wet room tray available for vinyl flooring. Its compact size is close to one metre square. The small size of the tray helps the water in shower area to find its way to the drain faster as the slope is steeper. This is an optimal wet room tray for creating a spacious shower in a restricted space.

Our most popular size tray, but this one offers the drain along the 1600mm side of the tray. The drain is 600mm long and is located 150mm from the edge. This is a great option for a shower that is wider than it is longer. Our Wet Room Shower Trays with Linear drains for tiled floors are the most versatile shower former you will find. They come with an integrated 600mm linear drain and are available in various sizes with different drain positions.

Each Tray's Advanced 3 piece drain offers plenty of flexibility and safety as well. The integrated plastic channel is factory installed into the tray assuring a water tight seal and allowing for the waste trap to be connected anywhere along the channel. The 304 grade stainless steel frame and cover make up the remaining parts of the drain. They are available in a variety of PVD coated colours and finishes. The frame is height adjustable to match the finished floor height. It also offers secondary drainage in case water were to ever penetrate the floor covering it will find its way to the drain. The cover itself is reversible, allowing you to either leave it right side up for a stainless steel finish to the cover or flipping it over and tiling inside for a tiled finish.

These XPS foam Trays have a 4 way slope machine cut into with an estimated 1-2% gradient fall. The bottom side of the tray is level and the integrated channel does not protrude below the tray allowing for both timber and concrete floor installation. Furthermore the hole (hole cutter provided) for the waste trap is drilled on site by the installer making avoiding joists that much simpler. Although the tray provides great thermal and acoustic insulation it is not structural so it will require to be supported throughout its entirety. The Trays are trim-able and can be cut down to a specific size or to avoid corners or match uneven walls or irregular angles.

Our most popular size tray, but this one offers the drain along the 1850mm side of the tray. The drain is 600mm long and is located 150mm from the edge. This is a great option for a shower that is wider than it is longer. Our Wet Room Shower Trays with Linear drains for tiled floors are the most versatile shower former you will find. They come with an integrated 600mm linear drain and are available in various sizes with different drain positions.

Each Tray's Advanced 3 piece drain offers plenty of flexibility and safety as well. The integrated plastic channel is factory installed into the tray assuring a water tight seal and allowing for the waste trap to be connected anywhere along the channel. The 304 grade stainless steel frame and cover make up the remaining parts of the drain. They are available in a variety of PVD coated colours and finishes. The frame is height adjustable to match the finished floor height. It also offers secondary drainage in case water were to ever penetrate the floor covering it will find its way to the drain. The cover itself is reversible, allowing you to either leave it right side up for a stainless steel finish to the cover or flipping it over and tiling inside for a tiled finish.

These XPS foam Trays have a 4 way slope machine cut into with an estimated 1-2% gradient fall. The bottom side of the tray is level and the integrated channel does not protrude below the tray allowing for both timber and concrete floor installation. Furthermore the hole (hole cutter provided) for the waste trap is drilled on site by the installer making avoiding joists that much simpler. Although the tray provides great thermal and acoustic insulation it is not structural so it will require to be supported throughout its entirety. The Trays are trim-able and can be cut down to a specific size or to avoid corners or match uneven walls or irregular angles.

Our most popular size tray, but this one offers the drain along the 1200mm side of the tray. The drain is 600mm long and is located 150mm from the edge. This is a great option for a shower that is wider than it is longer. Our Wet Room Shower Trays with Linear drains for tiled floors are the most versatile shower former you will find. They come with an integrated 600mm linear drain and are available in various sizes with different drain positions.

Each Tray's Advanced 3 piece drain offers plenty of flexibility and safety as well. The integrated plastic channel is factory installed into the tray assuring a water tight seal and allowing for the waste trap to be connected anywhere along the channel. The 304 grade stainless steel frame and cover make up the remaining parts of the drain. They are available in a variety of PVD coated colours and finishes. The frame is height adjustable to match the finished floor height. It also offers secondary drainage in case water were to ever penetrate the floor covering it will find its way to the drain. The cover itself is reversible, allowing you to either leave it right side up for a stainless steel finish to the cover or flipping it over and tiling inside for a tiled finish.

These XPS foam Trays have a 4 way slope machine cut into with an estimated 1-2% gradient fall. The bottom side of the tray is level and the integrated channel does not protrude below the tray allowing for both timber and concrete floor installation. Furthermore the hole (hole cutter provided) for the waste trap is drilled on site by the installer making avoiding joists that much simpler. Although the tray provides great thermal and acoustic insulation it is not structural so it will require to be supported throughout its entirety. The Trays are trim-able and can be cut down to a specific size or to avoid corners or match uneven walls or irregular angles.

Our most popular size tray, but this one offers the drain along the 1500mm side of the tray. The drain is 600mm long and is located 150mm from the edge. This is a great option for a shower that is wider than it is longer. Our Wet Room Shower Trays with Linear drains for tiled floors are the most versatile shower former you will find. They come with an integrated 600mm linear drain and are available in various sizes with different drain positions.

Each Tray's Advanced 3 piece drain offers plenty of flexibility and safety as well. The integrated plastic channel is factory installed into the tray assuring a water tight seal and allowing for the waste trap to be connected anywhere along the channel. The 304 grade stainless steel frame and cover make up the remaining parts of the drain. They are available in a variety of PVD coated colours and finishes. The frame is height adjustable to match the finished floor height. It also offers secondary drainage in case water were to ever penetrate the floor covering it will find its way to the drain. The cover itself is reversible, allowing you to either leave it right side up for a stainless steel finish to the cover or flipping it over and tiling inside for a tiled finish.

These XPS foam Trays have a 4 way slope machine cut into with an estimated 1-2% gradient fall. The bottom side of the tray is level and the integrated channel does not protrude below the tray allowing for both timber and concrete floor installation. Furthermore the hole (hole cutter provided) for the waste trap is drilled on site by the installer making avoiding joists that much simpler. Although the tray provides great thermal and acoustic insulation it is not structural so it will require to be supported throughout its entirety. The Trays are trim-able and can be cut down to a specific size or to avoid corners or match uneven walls or irregular angles.

Our most popular size tray, but this one offers the drain along the 1200mm side of the tray. The drain is 600mm long and is located 150mm from the edge. This is a great option for a shower that is wider than it is longer. Our Wet Room Shower Trays with Linear drains for tiled floors are the most versatile shower former you will find. They come with an integrated 600mm linear drain and are available in various sizes with different drain positions.

Each Tray's Advanced 3 piece drain offers plenty of flexibility and safety as well. The integrated plastic channel is factory installed into the tray assuring a water tight seal and allowing for the waste trap to be connected anywhere along the channel. The 304 grade stainless steel frame and cover make up the remaining parts of the drain. They are available in a variety of PVD coated colours and finishes. The frame is height adjustable to match the finished floor height. It also offers secondary drainage in case water were to ever penetrate the floor covering it will find its way to the drain. The cover itself is reversible, allowing you to either leave it right side up for a stainless steel finish to the cover or flipping it over and tiling inside for a tiled finish.

These XPS foam Trays have a 4 way slope machine cut into with an estimated 1-2% gradient fall. The bottom side of the tray is level and the integrated channel does not protrude below the tray allowing for both timber and concrete floor installation. Furthermore the hole (hole cutter provided) for the waste trap is drilled on site by the installer making avoiding joists that much simpler. Although the tray provides great thermal and acoustic insulation it is not structural so it will require to be supported throughout its entirety. The Trays are trim-able and can be cut down to a specific size or to avoid corners or match uneven walls or irregular angles.

Our most popular size tray, but this one offers the drain along the 1500mm side of the tray. The drain is 600mm long and is located 150mm from the edge. This is a great option for a shower that is wider than it is longer. Our Wet Room Shower Trays with Linear drains for tiled floors are the most versatile shower former you will find. They come with an integrated 600mm linear drain and are available in various sizes with different drain positions.

Each Tray's Advanced 3 piece drain offers plenty of flexibility and safety as well. The integrated plastic channel is factory installed into the tray assuring a water tight seal and allowing for the waste trap to be connected anywhere along the channel. The 304 grade stainless steel frame and cover make up the remaining parts of the drain. They are available in a variety of PVD coated colours and finishes. The frame is height adjustable to match the finished floor height. It also offers secondary drainage in case water were to ever penetrate the floor covering it will find its way to the drain. The cover itself is reversible, allowing you to either leave it right side up for a stainless steel finish to the cover or flipping it over and tiling inside for a tiled finish.

These XPS foam Trays have a 4 way slope machine cut into with an estimated 1-2% gradient fall. The bottom side of the tray is level and the integrated channel does not protrude below the tray allowing for both timber and concrete floor installation. Furthermore the hole (hole cutter provided) for the waste trap is drilled on site by the installer making avoiding joists that much simpler. Although the tray provides great thermal and acoustic insulation it is not structural so it will require to be supported throughout its entirety. The Trays are trim-able and can be cut down to a specific size or to avoid corners or match uneven walls or irregular angles.

Experience Seamless Luxury with Our Microcement-Ready WetroomStop Side Shower Tray:

Crafted at a substantial 40mm thickness, our shower base ensures a smooth, level-access transition into your shower space, eliminating the need for cumbersome steps. Engineered with XPS foam and reinforced with fibreglass mesh on both sides, our tray boasts unparalleled strength and durability. Its flexible cement coating, specially hardened for microcement application, guarantees a flawless surface for your desired finish.

Our tray's innovative 3-piece drain system offers both versatility and safety. The factory-installed steel drain ensures a watertight seal, while the 304 grade stainless steel frame and cover provide enduring quality. With a range of PVD coated colours and finishes available, you can customise your drain to match your aesthetic preferences. Plus, the height-adjustable frame accommodates various floor heights, as well as secondary drainage functionality.

Designed for precision, our trays feature a 4-way slope machine cut with a subtle 1-2% fall, ensuring efficient water drainage. The integrated channel sits flush with the tray's bottom surface, allowing for seamless microcement floor installation. And for ultimate customization, our trimmable trays can be effortlessly adjusted to fit specific dimensions, accommodate irregular angles, or match uneven walls.

Elevate your shower experience with our Microcement-Ready WetroomStop Shower Tray Collection – where functionality meets sophistication.

Our most popular size tray, but this one offers the drain along the 1400mm side of the tray. The drain is 600mm long and is located 150mm from the edge. This is a great option for a shower that is wider than it is longer. Our Wet Room Shower Trays with Linear drains for tiled floors are the most versatile shower former you will find. They come with an integrated 600mm linear drain and are available in various sizes with different drain positions.

Each Tray's Advanced 3 piece drain offers plenty of flexibility and safety as well. The integrated plastic channel is factory installed into the tray assuring a water tight seal and allowing for the waste trap to be connected anywhere along the channel. The 304 grade stainless steel frame and cover make up the remaining parts of the drain. They are available in a variety of PVD coated colours and finishes. The frame is height adjustable to match the finished floor height. It also offers secondary drainage in case water were to ever penetrate the floor covering it will find its way to the drain. The cover itself is reversible, allowing you to either leave it right side up for a stainless steel finish to the cover or flipping it over and tiling inside for a tiled finish.

These XPS foam Trays have a 4 way slope machine cut into with an estimated 1-2% gradient fall. The bottom side of the tray is level and the integrated channel does not protrude below the tray allowing for both timber and concrete floor installation. Furthermore the hole (hole cutter provided) for the waste trap is drilled on site by the installer making avoiding joists that much simpler. Although the tray provides great thermal and acoustic insulation it is not structural so it will require to be supported throughout its entirety. The Trays are trim-able and can be cut down to a specific size or to avoid corners or match uneven walls or irregular angles.

Our most popular size tray, but this one offers the drain along the 1600mm side of the tray. The drain is 600mm long and is located 150mm from the edge. This is a great option for a shower that is wider than it is longer. Our Wet Room Shower Trays with Linear drains for tiled floors are the most versatile shower former you will find. They come with an integrated 600mm linear drain and are available in various sizes with different drain positions.

Each Tray's Advanced 3 piece drain offers plenty of flexibility and safety as well. The integrated plastic channel is factory installed into the tray assuring a water tight seal and allowing for the waste trap to be connected anywhere along the channel. The 304 grade stainless steel frame and cover make up the remaining parts of the drain. They are available in a variety of PVD coated colours and finishes. The frame is height adjustable to match the finished floor height. It also offers secondary drainage in case water were to ever penetrate the floor covering it will find its way to the drain. The cover itself is reversible, allowing you to either leave it right side up for a stainless steel finish to the cover or flipping it over and tiling inside for a tiled finish.

These XPS foam Trays have a 4 way slope machine cut into with an estimated 1-2% gradient fall. The bottom side of the tray is level and the integrated channel does not protrude below the tray allowing for both timber and concrete floor installation. Furthermore the hole (hole cutter provided) for the waste trap is drilled on site by the installer making avoiding joists that much simpler. Although the tray provides great thermal and acoustic insulation it is not structural so it will require to be supported throughout its entirety. The Trays are trim-able and can be cut down to a specific size or to avoid corners or match uneven walls or irregular angles.

Our most popular size tray, but this one offers the drain along the 1850mm side of the tray. The drain is 600mm long and is located 150mm from the edge. This is a great option for a shower that is wider than it is longer. Our Wet Room Shower Trays with Linear drains for tiled floors are the most versatile shower former you will find. They come with an integrated 600mm linear drain and are available in various sizes with different drain positions.

Each Tray's Advanced 3 piece drain offers plenty of flexibility and safety as well. The integrated plastic channel is factory installed into the tray assuring a water tight seal and allowing for the waste trap to be connected anywhere along the channel. The 304 grade stainless steel frame and cover make up the remaining parts of the drain. They are available in a variety of PVD coated colours and finishes. The frame is height adjustable to match the finished floor height. It also offers secondary drainage in case water were to ever penetrate the floor covering it will find its way to the drain. The cover itself is reversible, allowing you to either leave it right side up for a stainless steel finish to the cover or flipping it over and tiling inside for a tiled finish.

These XPS foam Trays have a 4 way slope machine cut into with an estimated 1-2% gradient fall. The bottom side of the tray is level and the integrated channel does not protrude below the tray allowing for both timber and concrete floor installation. Furthermore the hole (hole cutter provided) for the waste trap is drilled on site by the installer making avoiding joists that much simpler. Although the tray provides great thermal and acoustic insulation it is not structural so it will require to be supported throughout its entirety. The Trays are trim-able and can be cut down to a specific size or to avoid corners or match uneven walls or irregular angles.

Our most popular size tray, but this one offers the drain along the 1200mm side of the tray. The drain is 600mm long and is located 150mm from the edge. This is a great option for a shower that is wider than it is longer. Our Wet Room Shower Trays with Linear drains for tiled floors are the most versatile shower former you will find. They come with an integrated 600mm linear drain and are available in various sizes with different drain positions.

Each Tray's Advanced 3 piece drain offers plenty of flexibility and safety as well. The integrated plastic channel is factory installed into the tray assuring a water tight seal and allowing for the waste trap to be connected anywhere along the channel. The 304 grade stainless steel frame and cover make up the remaining parts of the drain. They are available in a variety of PVD coated colours and finishes. The frame is height adjustable to match the finished floor height. It also offers secondary drainage in case water were to ever penetrate the floor covering it will find its way to the drain. The cover itself is reversible, allowing you to either leave it right side up for a stainless steel finish to the cover or flipping it over and tiling inside for a tiled finish.

These XPS foam Trays have a 4 way slope machine cut into with an estimated 1-2% gradient fall. The bottom side of the tray is level and the integrated channel does not protrude below the tray allowing for both timber and concrete floor installation. Furthermore the hole (hole cutter provided) for the waste trap is drilled on site by the installer making avoiding joists that much simpler. Although the tray provides great thermal and acoustic insulation it is not structural so it will require to be supported throughout its entirety. The Trays are trim-able and can be cut down to a specific size or to avoid corners or match uneven walls or irregular angles.