End Drain

This popular size tray is an excellent option for a walk-in shower where space may be limited. The drain is located along the short end, 150mm from the edge, designating one end as the shower area and the far end as the entrance to the shower. Our Wet Room Shower Trays with Linear drains for tiled floors are the most versatile shower former you will find. They come with an integrated 600mm linear drain and are available in various sizes with different drain positions.

Each Tray's Advanced 3 piece drain offers plenty of flexibility and safety as well. The integrated plastic channel is factory installed into the tray assuring a water tight seal and allowing for the waste trap to be connected anywhere along the channel. The 304 grade stainless steel frame and cover make up the remaining parts of the drain. They are available in a variety of PVD coated colours and finishes. The frame is height adjustable to match the finished floor height. It also offers secondary drainage in case water were to ever penetrate the floor covering it will find its way to the drain. The cover itself is reversible, allowing you to either leave it right side up for a stainless steel finish to the cover or flipping it over and tiling inside for a tiled finish.

These XPS foam Trays have a 4 way slope machine cut into with an estimated 1-2% gradient fall. The bottom side of the tray is level and the integrated channel does not protrude below the tray allowing for both timber and concrete floor installation. Furthermore the hole (hole cutter provided) for the waste trap is drilled on site by the installer making avoiding joists that much simpler. Although the tray provides great thermal and acoustic insulation it is not structural so it will require to be supported throughout its entirety. The Trays are trim-able and can be cut down to a specific size or to avoid corners or match uneven walls or irregular angles.

The 900 mm x 900 mm shower base is 30 mm thick and is designed to be tiled over, providing level access into the shower without a step up. The shower base is produced from XPS foam and re-enforced on both sides with a fibreglass mesh and coated with a flexible cement. This surface is ready to tile onto. It's lightweight and flexible enough to absorb movement within the structural floor.

The XPS foam has great acoustic properties and therefore is an excellent choice for showers here in the UK, when you can generally hear everything that's going on upstairs! It can be easily trimmed if necessary, say around pipes or other obstacles, or if you are fitting a shower that is not quite the size of the tray.

The shower base has a machined slope cut into it, providing a 4 way fall from each corner to the drain. The enveloped shaped pattern helps guide the water toward the channel, eliminating the need to create fall on your own.

The most popular size tray. Allows ample space for showering and does not take up too much space in the room. The 600mm linear drain channel is parallel to the 900mm side and is 150mm away from the edge of the tray. Our Wet Room Shower Trays with Linear drains for tiled floors are the most versatile shower former you will find. They come with an integrated 600mm linear drain and are available in various sizes with different drain positions.

Each Tray's Advanced 3 piece drain offers plenty of flexibility and safety as well. The integrated plastic channel is factory installed into the tray assuring a water tight seal and allowing for the waste trap to be connected anywhere along the channel. The 304 grade stainless steel frame and cover make up the remaining parts of the drain. They are available in a variety of PVD coated colours and finishes. The frame is height adjustable to match the finished floor height. It also offers secondary drainage in case water were to ever penetrate the floor covering it will find its way to the drain. The cover itself is reversible, allowing you to either leave it right side up for a stainless steel finish to the cover or flipping it over and tiling inside for a tiled finish.

These XPS foam Trays have a 4 way slope machine cut into with an estimated 1-2% gradient fall. The bottom side of the tray is level and the integrated channel does not protrude below the tray allowing for both timber and concrete floor installation. Furthermore the hole (hole cutter provided) for the waste trap is drilled on site by the installer making avoiding joists that much simpler. Although the tray provides great thermal and acoustic insulation it is not structural so it will require to be supported throughout its entirety. The Trays are trim-able and can be cut down to a specific size or to avoid corners or match uneven walls or irregular angles.

The 900 mm x 1200 mm shower base is 30 mm thick and is designed to be tiled over, providing level access into the shower without a step up. The shower base is produced from XPS foam and re-enforced on both sides with a fibreglass mesh and coated with a flexible cement. This surface is ready to tile onto. It's lightweight and flexible enough to absorb movement within the structural floor.

The XPS foam has great acoustic properties and therefore is an excellent choice for showers here in the UK, when you can generally hear everything that's going on upstairs! It can be easily trimmed if necessary, say around pipes or other obstacles, or if you are fitting a shower that is not quite the size of the tray.

The shower base has a machined slope cut into it, providing a 4 way fall from each corner to the drain. The enveloped shaped pattern helps guide the water toward the channel, eliminating the need to create fall on your own.

The Top Tier wet room kit walk-in shower tray, measuring 1000 x 1500 mm, represents a standard former size. Engineered to be low level, it provides generous shower space while maintaining remarkable versatility, compatible with various shower screens and doors. Its square shape allows for placement in any part of the room, whether neatly tucked into a corner or positioned elsewhere, offering flexibility in room layout.

Each Tray's Advanced 3 piece drain offers plenty of flexibility and safety as well. The integrated plastic channel is factory installed into the tray assuring a water tight seal and allowing for the waste trap to be connected anywhere along the channel. The 304 grade stainless steel frame and cover make up the remaining parts of the drain. They are available in a variety of PVD coated colours and finishes. The frame is height adjustable to match the finished floor height. It also offers secondary drainage in case water were to ever penetrate the floor covering it will find its way to the drain. The cover itself is reversible, allowing you to either leave it right side up for a stainless steel finish to the cover or flipping it over and tiling inside for a tiled finish.

These XPS foam Trays have a Two-Way double slope machine cut into with an estimated 1-2% fall. The bottom side of the tray is level and the integrated channel does not protrude below the tray allowing for both timber and concrete floor installation. Furthermore the hole (hole cutter provided) for the waste trap is drilled on site by the installer making avoiding joists that much simpler. Although the tray provides great thermal and acoustic insulation it is not structural so it will require to be supported throughout its entirety. The Trays are trim-able and can be cut down to a specific size or to avoid corners or match uneven walls or irregular angles.

The 900 mm x 1500 mm shower base is 30 mm thick and is designed to be tiled over, providing level access into the shower without a step up. The shower base is produced from XPS foam and re-enforced on both sides with a fibreglass mesh and coated with a flexible cement. This surface is ready to tile onto. It's lightweight and flexible enough to absorb movement within the structural floor.

The XPS foam has great acoustic properties and therefore is an excellent choice for showers here in the UK, when you can generally hear everything that's going on upstairs! It can be easily trimmed if necessary, say around pipes or other obstacles, or if you are fitting a shower that is not quite the size of the tray.

The shower base has a machined slope cut into it, providing a 4 way fall from each corner to the drain. The enveloped shaped pattern helps guide the water toward the channel, eliminating the need to create fall on your own.

The 800 mm x 800 mm shower base is 30 mm thick and is designed to be tiled over, providing level access into the shower without a step up. The shower base is produced from XPS foam and re-enforced on both sides with a fibreglass mesh and coated with a flexible cement. This surface is ready to tile onto. It's lightweight and flexible enough to absorb movement within the structural floor.

The XPS foam has great acoustic properties and therefore is an excellent choice for showers here in the UK, when you can generally hear everything that's going on upstairs! It can be easily trimmed if necessary, say around pipes or other obstacles, or if you are fitting a shower that is not quite the size of the tray.

The shower base has a machined slope cut into it, providing a 4 way fall from each corner to the drain. The enveloped shaped pattern helps guide the water toward the channel, eliminating the need to create fall on your own.

This longer but narrow tray is a great option for a small shower with a comfortable entrance. The drain is located 150mm from the short end  while the far end of the tray still has a sloped floor. Our Wet Room Shower Trays with Linear drains for tiled floors are the most versatile shower former you will find. They come with an integrated 600mm linear drain and are available in various sizes with different drain positions.

Each Tray's Advanced 3 piece drain offers plenty of flexibility and safety as well. The integrated plastic channel is factory installed into the tray assuring a water tight seal and allowing for the waste trap to be connected anywhere along the channel. The 304 grade stainless steel frame and cover make up the remaining parts of the drain. They are available in a variety of PVD coated colours and finishes. The frame is height adjustable to match the finished floor height. It also offers secondary drainage in case water were to ever penetrate the floor covering it will find its way to the drain. The cover itself is reversible, allowing you to either leave it right side up for a stainless steel finish to the cover or flipping it over and tiling inside for a tiled finish.

These XPS foam Trays have a 4 way slope machine cut into with an estimated 1-2% gradient fall. The bottom side of the tray is level and the integrated channel does not protrude below the tray allowing for both timber and concrete floor installation. Furthermore the hole (hole cutter provided) for the waste trap is drilled on site by the installer making avoiding joists that much simpler. Although the tray provides great thermal and acoustic insulation it is not structural so it will require to be supported throughout its entirety. The Trays are trim-able and can be cut down to a specific size or to avoid corners or match uneven walls or irregular angles.

The 1000 mm x 1000 mm shower base is 30 mm thick and is designed to be tiled over, providing level access into the shower without a step up. The shower base is produced from XPS foam and re-enforced on both sides with a fibreglass mesh and coated with a flexible cement. This surface is ready to tile onto. It's lightweight and flexible enough to absorb movement within the structural floor.

The XPS foam has great acoustic properties and therefore is an excellent choice for showers here in the UK, when you can generally hear everything that's going on upstairs! It can be easily trimmed if necessary, say around pipes or other obstacles, or if you are fitting a shower that is not quite the size of the tray.

The shower base has a machined slope cut into it, providing a 4 way fall from each corner to the drain. The enveloped shaped pattern helps guide the water toward the channel, eliminating the need to create fall on your own.

The wet room shower former, measuring 900 x 1600 mm, stands as one of the largest tray bases available in our store. If you notice unused space in your bathroom and aspire to add that extra bathroom you've always desired, this spacious walk-in shower tray is an ideal choice. It not only provides ample room but also imparts a warm and luxurious feeling, enhancing your daily rituals with the pleasure of beginning and ending your day in a beautiful setting.

Each Tray's Advanced 3 piece drain offers plenty of flexibility and safety as well. The integrated plastic channel is factory installed into the tray assuring a water tight seal and allowing for the waste trap to be connected anywhere along the channel. The 304 grade stainless steel frame and cover make up the remaining parts of the drain. They are available in a variety of PVD coated colours and finishes. The frame is height adjustable to match the finished floor height. It also offers secondary drainage in case water were to ever penetrate the floor covering it will find its way to the drain. The cover itself is reversible, allowing you to either leave it right side up for a stainless steel finish to the cover or flipping it over and tiling inside for a tiled finish.

These XPS foam Trays have a One-Way single slope machine cut into with an estimated 1-2% fall. The bottom side of the tray is level and the integrated channel does not protrude below the tray allowing for both timber and concrete floor installation. Furthermore the hole (hole cutter provided) for the waste trap is drilled on site by the installer making avoiding joists that much simpler. Although the tray provides great thermal and acoustic insulation it is not structural so it will require to be supported throughout its entirety. The Trays are trim-able and can be cut down to a specific size or to avoid corners or match uneven walls or irregular angles.

The 1200 mm x 1200 mm shower base is 30 mm thick and is designed to be tiled over, providing level access into the shower without a step up. The shower base is produced from XPS foam and re-enforced on both sides with a fibreglass mesh and coated with a flexible cement. This surface is ready to tile onto. It's lightweight and flexible enough to absorb movement within the structural floor.

The XPS foam has great acoustic properties and therefore is an excellent choice for showers here in the UK, when you can generally hear everything that's going on upstairs! It can be easily trimmed if necessary, say around pipes or other obstacles, or if you are fitting a shower that is not quite the size of the tray.

The shower base has a machined slope cut into it, providing a 4 way fall from each corner to the drain. The enveloped shaped pattern helps guide the water toward the channel, eliminating the need to create fall on your own.

The largest square shower tray, measuring 1200 x 1200 mm, accommodates larger shower areas and ensures a comfortable and easily accessible shower experience. While this size kit may not be suitable for the smallest bathrooms, it features an integrated, elongated drain that offers a modern aesthetic. With the floor appearing as a single expanse and only a drainage hole visible, it creates a seamless look that enhances the feeling of space in the bathroom.

Each Tray's Advanced 3 piece drain offers plenty of flexibility and safety as well. The integrated plastic channel is factory installed into the tray assuring a water tight seal and allowing for the waste trap to be connected anywhere along the channel. The 304 grade stainless steel frame and cover make up the remaining parts of the drain. They are available in a variety of PVD coated colours and finishes. The frame is height adjustable to match the finished floor height. It also offers secondary drainage in case water were to ever penetrate the floor covering it will find its way to the drain. The cover itself is reversible, allowing you to either leave it right side up for a stainless steel finish to the cover or flipping it over and tiling inside for a tiled finish.

These XPS foam Trays have a One-Way single slope machine cut into with an estimated 1-2% fall. The bottom side of the tray is level and the integrated channel does not protrude below the tray allowing for both timber and concrete floor installation. Furthermore the hole (hole cutter provided) for the waste trap is drilled on site by the installer making avoiding joists that much simpler. Although the tray provides great thermal and acoustic insulation it is not structural so it will require to be supported throughout its entirety. The Trays are trim-able and can be cut down to a specific size or to avoid corners or match uneven walls or irregular angles.

The 1000 mm x 1200 mm shower base is 30 mm thick and is designed to be tiled over, providing level access into the shower without a step up. The shower base is produced from XPS foam and re-enforced on both sides with a fibreglass mesh and coated with a flexible cement. This surface is ready to tile onto. It's lightweight and flexible enough to absorb movement within the structural floor.

The XPS foam has great acoustic properties and therefore is an excellent choice for showers here in the UK, when you can generally hear everything that's going on upstairs! It can be easily trimmed if necessary, say around pipes or other obstacles, or if you are fitting a shower that is not quite the size of the tray.

The shower base has a machined slope cut into it, providing a 4 way fall from each corner to the drain. The enveloped shaped pattern helps guide the water toward the channel, eliminating the need to create fall on your own.

Very popular size tray. Provides an excellent walk in shower size where the opening for the entrance can remain open. The drain is 600mm long and is parallel to the 900mm side. It is located 150mm from the edge of the tray. Our Wet Room Shower Trays with Linear drains for tiled floors are the most versatile shower former you will find. They come with an integrated 600mm linear drain and are available in various sizes with different drain positions.

Each Tray's Advanced 3 piece drain offers plenty of flexibility and safety as well. The integrated plastic channel is factory installed into the tray assuring a water tight seal and allowing for the waste trap to be connected anywhere along the channel. The 304 grade stainless steel frame and cover make up the remaining parts of the drain. They are available in a variety of PVD coated colours and finishes. The frame is height adjustable to match the finished floor height. It also offers secondary drainage in case water were to ever penetrate the floor covering it will find its way to the drain. The cover itself is reversible, allowing you to either leave it right side up for a stainless steel finish to the cover or flipping it over and tiling inside for a tiled finish.

These XPS foam Trays have a 4 way slope machine cut into with an estimated 1-2% gradient fall. The bottom side of the tray is level and the integrated channel does not protrude below the tray allowing for both timber and concrete floor installation. Furthermore the hole (hole cutter provided) for the waste trap is drilled on site by the installer making avoiding joists that much simpler. Although the tray provides great thermal and acoustic insulation it is not structural so it will require to be supported throughout its entirety. The Trays are trim-able and can be cut down to a specific size or to avoid corners or match uneven walls or irregular angles.

The 1000 mm x 1500 mm shower base is 30 mm thick and is designed to be tiled over, providing level access into the shower without a step up. The shower base is produced from XPS foam and re-enforced on both sides with a fibreglass mesh and coated with a flexible cement. This surface is ready to tile onto. It's lightweight and flexible enough to absorb movement within the structural floor.

The XPS foam has great acoustic properties and therefore is an excellent choice for showers here in the UK, when you can generally hear everything that's going on upstairs! It can be easily trimmed if necessary, say around pipes or other obstacles, or if you are fitting a shower that is not quite the size of the tray.

The shower base has a machined slope cut into it, providing a 4 way fall from each corner to the drain. The enveloped shaped pattern helps guide the water toward the channel, eliminating the need to create fall on your own.

The Top Tier wet room kit walk-in shower tray, sized at 900 x 1400 mm, represents a typical former size. Designed to be low level, it provides ample shower space while offering remarkable versatility, compatible with various shower screens and doors. Its square shape enables placement in any part of the room, whether neatly tucked into a corner or positioned elsewhere, providing flexibility in room layout.

Each Tray's Advanced 3 piece drain offers plenty of flexibility and safety as well. The integrated plastic channel is factory installed into the tray assuring a water tight seal and allowing for the waste trap to be connected anywhere along the channel. The 304 grade stainless steel frame and cover make up the remaining parts of the drain. They are available in a variety of PVD coated colours and finishes. The frame is height adjustable to match the finished floor height. It also offers secondary drainage in case water were to ever penetrate the floor covering it will find its way to the drain. The cover itself is reversible, allowing you to either leave it right side up for a stainless steel finish to the cover or flipping it over and tiling inside for a tiled finish.

These XPS foam Trays have a Two-Way double slope machine cut into with an estimated 1-2% fall. The bottom side of the tray is level and the integrated channel does not protrude below the tray allowing for both timber and concrete floor installation. Furthermore the hole (hole cutter provided) for the waste trap is drilled on site by the installer making avoiding joists that much simpler. Although the tray provides great thermal and acoustic insulation it is not structural so it will require to be supported throughout its entirety. The Trays are trim-able and can be cut down to a specific size or to avoid corners or match uneven walls or irregular angles.

The largest wet room kit, measuring 900 x 1850 mm, features a shower tray designed for installation in rooms with ample space. A walk-in shower flooring not only expands the bathroom area but also introduces a modern, simple, and fresh aesthetic, enhancing the attractiveness of the restroom. Moreover, it provides easy accessibility for individuals with mobility issues. The Showerlay of this size is particularly suitable for large tile formats, although it can still accommodate even small mosaic tiles if desired.

Each Tray's Advanced 3 piece drain offers plenty of flexibility and safety as well. The integrated plastic channel is factory installed into the tray assuring a water tight seal and allowing for the waste trap to be connected anywhere along the channel. The 304 grade stainless steel frame and cover make up the remaining parts of the drain. They are available in a variety of PVD coated colours and finishes. The frame is height adjustable to match the finished floor height. It also offers secondary drainage in case water were to ever penetrate the floor covering it will find its way to the drain. The cover itself is reversible, allowing you to either leave it right side up for a stainless steel finish to the cover or flipping it over and tiling inside for a tiled finish.

These XPS foam Trays have a Two-Way double slope machine cut into with an estimated 1-2% fall. The bottom side of the tray is level and the integrated channel does not protrude below the tray allowing for both timber and concrete floor installation. Furthermore the hole (hole cutter provided) for the waste trap is drilled on site by the installer making avoiding joists that much simpler. Although the tray provides great thermal and acoustic insulation it is not structural so it will require to be supported throughout its entirety. The Trays are trim-able and can be cut down to a specific size or to avoid corners or match uneven walls or irregular angles.

The 800 mm x 1200 mm shower base is 30 mm thick and is designed to be tiled over, providing level access into the shower without a step up. The shower base is produced from XPS foam and re-enforced on both sides with a fibreglass mesh and coated with a flexible cement. This surface is ready to tile onto. It's lightweight and flexible enough to absorb movement within the structural floor.

The XPS foam has great acoustic properties and therefore is an excellent choice for showers here in the UK, when you can generally hear everything that's going on upstairs! It can be easily trimmed if necessary, say around pipes or other obstacles, or if you are fitting a shower that is not quite the size of the tray.

The shower base has a machined slope cut into it, providing a 4 way fall from each corner to the drain. The enveloped shaped pattern helps guide the water toward the channel, eliminating the need to create fall on your own.

The 800 mm x 1500 mm shower base is 30 mm thick and is designed to be tiled over, providing level access into the shower without a step up. The shower base is produced from XPS foam and re-enforced on both sides with a fibreglass mesh and coated with a flexible cement. This surface is ready to tile onto. It's lightweight and flexible enough to absorb movement within the structural floor.

The XPS foam has great acoustic properties and therefore is an excellent choice for showers here in the UK, when you can generally hear everything that's going on upstairs! It can be easily trimmed if necessary, say around pipes or other obstacles, or if you are fitting a shower that is not quite the size of the tray.

The shower base has a machined slope cut into it, providing a 4 way fall from each corner to the drain. The enveloped shaped pattern helps guide the water toward the channel, eliminating the need to create fall on your own.

This popular size tray is an excellent option for a walk-in shower where space may be limited. The drain is located along the short end, 150mm from the edge, designating one end as the shower area and the far end as the entrance to the shower. Our Wet Room Shower Trays with Linear drains for tiled floors are the most versatile shower former you will find. They come with an integrated 600mm linear drain and are available in various sizes with different drain positions.

Each Tray's Advanced 3 piece drain offers plenty of flexibility and safety as well. The integrated plastic channel is factory installed into the tray assuring a water tight seal and allowing for the waste trap to be connected anywhere along the channel. The 304 grade stainless steel frame and cover make up the remaining parts of the drain. They are available in a variety of PVD coated colours and finishes. The frame is height adjustable to match the finished floor height. It also offers secondary drainage in case water were to ever penetrate the floor covering it will find its way to the drain. The cover itself is reversible, allowing you to either leave it right side up for a stainless steel finish to the cover or flipping it over and tiling inside for a tiled finish.

These XPS foam Trays have a 4 way slope machine cut into with an estimated 1-2% gradient fall. The bottom side of the tray is level and the integrated channel does not protrude below the tray allowing for both timber and concrete floor installation. Furthermore the hole (hole cutter provided) for the waste trap is drilled on site by the installer making avoiding joists that much simpler. Although the tray provides great thermal and acoustic insulation it is not structural so it will require to be supported throughout its entirety. The Trays are trim-able and can be cut down to a specific size or to avoid corners or match uneven walls or irregular angles.

The 900 mm x 1400 mm shower base is 30 mm thick and is designed to be tiled over, providing level access into the shower without a step up. The shower base is produced from XPS foam and re-enforced on both sides with a fibreglass mesh and coated with a flexible cement. This surface is ready to tile onto. It's lightweight and flexible enough to absorb movement within the structural floor.

The XPS foam has great acoustic properties and therefore is an excellent choice for showers here in the UK, when you can generally hear everything that's going on upstairs! It can be easily trimmed if necessary, say around pipes or other obstacles, or if you are fitting a shower that is not quite the size of the tray.

The shower base has a machined slope cut into it, providing a 4 way fall from each corner to the drain. The enveloped shaped pattern helps guide the water toward the channel, eliminating the need to create fall on your own.

Very compact tray, square in shape, can be installed with the drain along any side. The 600mm linear drain is located 150mm for the edge of the tray and has 150mm of tray on both ends. Our Wet Room Shower Trays with Linear drains for tiled floors are the most versatile shower former you will find. They come with an integrated 600mm linear drain and are available in various sizes with different drain positions.

Each Tray's Advanced 3 piece drain offers plenty of flexibility and safety as well. The integrated plastic channel is factory installed into the tray assuring a water tight seal and allowing for the waste trap to be connected anywhere along the channel. The 304 grade stainless steel frame and cover make up the remaining parts of the drain. They are available in a variety of PVD coated colours and finishes. The frame is height adjustable to match the finished floor height. It also offers secondary drainage in case water were to ever penetrate the floor covering it will find its way to the drain. The cover itself is reversible, allowing you to either leave it right side up for a stainless steel finish to the cover or flipping it over and tiling inside for a tiled finish.

These XPS foam Trays have a 4 way slope machine cut into with an estimated 1-2% gradient fall. The bottom side of the tray is level and the integrated channel does not protrude below the tray allowing for both timber and concrete floor installation. Furthermore the hole (hole cutter provided) for the waste trap is drilled on site by the installer making avoiding joists that much simpler. Although the tray provides great thermal and acoustic insulation it is not structural so it will require to be supported throughout its entirety. The Trays are trim-able and can be cut down to a specific size or to avoid corners or match uneven walls or irregular angles.

The 900 x 1200 mm shower kit is specifically crafted to provide a wet room tray suitable for timber floor level access. It's conveniently easy to resize, lightweight, and highly maneuverable. The contemporary, minimalist design of the wet room fosters relaxation for your body and rejuvenation for your mind.

Each Tray's Advanced 3 piece drain offers plenty of flexibility and safety as well. The integrated plastic channel is factory installed into the tray assuring a water tight seal and allowing for the waste trap to be connected anywhere along the channel. The 304 grade stainless steel frame and cover make up the remaining parts of the drain. They are available in a variety of PVD coated colours and finishes. The frame is height adjustable to match the finished floor height. It also offers secondary drainage in case water were to ever penetrate the floor covering it will find its way to the drain. The cover itself is reversible, allowing you to either leave it right side up for a stainless steel finish to the cover or flipping it over and tiling inside for a tiled finish.

These XPS foam Trays have a Two-Way double slope machine cut into with an estimated 1-2% fall. The bottom side of the tray is level and the integrated channel does not protrude below the tray allowing for both timber and concrete floor installation. Furthermore the hole (hole cutter provided) for the waste trap is drilled on site by the installer making avoiding joists that much simpler. Although the tray provides great thermal and acoustic insulation it is not structural so it will require to be supported throughout its entirety. The Trays are trim-able and can be cut down to a specific size or to avoid corners or match uneven walls or irregular angles.

The 900 mm x 1600 mm shower base is 30 mm thick and is designed to be tiled over, providing level access into the shower without a step up. The shower base is produced from XPS foam and re-enforced on both sides with a fibreglass mesh and coated with a flexible cement. This surface is ready to tile onto. It's lightweight and flexible enough to absorb movement within the structural floor.

The XPS foam has great acoustic properties and therefore is an excellent choice for showers here in the UK, when you can generally hear everything that's going on upstairs! It can be easily trimmed if necessary, say around pipes or other obstacles, or if you are fitting a shower that is not quite the size of the tray.

The shower base has a machined slope cut into it, providing a 4 way fall from each corner to the drain. The enveloped shaped pattern helps guide the water toward the channel, eliminating the need to create fall on your own.