Wet Room Shower Trays

The 800 mm x 1200 mm shower base is 30 mm thick and is designed to be tiled over, providing level access into the shower without a step up. The shower base is produced from XPS foam and re-enforced on both sides with a fibreglass mesh and coated with a flexible cement. This surface is ready to tile onto. It's lightweight and flexible enough to absorb movement within the structural floor.

The XPS foam has great acoustic properties and therefore is an excellent choice for showers here in the UK, when you can generally hear everything that's going on upstairs! It can be easily trimmed if necessary, say around pipes or other obstacles, or if you are fitting a shower that is not quite the size of the tray.

The shower base has a machined slope cut into it, providing a 4 way fall from each corner to the drain. The enveloped shaped pattern helps guide the water toward the channel, eliminating the need to create fall on your own.

The 800 mm x 1200 mm shower base is 20 mm thick and is designed to be tiled over, providing level access into the shower without a step up. The shower base is produced from XPS foam and re-enforced on both sides with a fibreglass mesh and coated with a flexible cement. This surface is ready to tile onto. It's lightweight and flexible enough to absorb movement within the structural floor.

The shower base has a machined slope cut into it, providing a 4 way fall from each corner to the drain. The drain is offset from the centre of the tray, creating a shower zone to one end of the tray. While leaving the other end is more of a walkway or entrance to the shower. This allows for the entrance to still have a gradual slope for water to flow back toward the drain.

The XPS foam has great acoustic properties and therefore is an excellent choice for showers here in the UK, when you can generally hear everything that's going on upstairs! It can be easily trimmed if necessary, say around pipes or other obstacles, or if you are fitting a shower that is not quite the size of the tray. The height of the drain is 10mm, however this can be extended to 17mm using the extension provided.

The most popular size tray. Allows ample space for showering and does not take up too much space in the room. The 600mm linear drain channel is parallel to the 900mm side and is 150mm away from the edge of the tray. Our Wet Room Shower Trays with Linear drains for tiled floors are the most versatile shower former you will find. They come with an integrated 600mm linear drain and are available in various sizes with different drain positions.

Each Tray's Advanced 3 piece drain offers plenty of flexibility and safety as well. The integrated plastic channel is factory installed into the tray assuring a water tight seal and allowing for the waste trap to be connected anywhere along the channel. The 304 grade stainless steel frame and cover make up the remaining parts of the drain. They are available in a variety of PVD coated colours and finishes. The frame is height adjustable to match the finished floor height. It also offers secondary drainage in case water were to ever penetrate the floor covering it will find its way to the drain. The cover itself is reversible, allowing you to either leave it right side up for a stainless steel finish to the cover or flipping it over and tiling inside for a tiled finish.

These XPS foam Trays have a 4 way slope machine cut into with an estimated 1-2% gradient fall. The bottom side of the tray is level and the integrated channel does not protrude below the tray allowing for both timber and concrete floor installation. Furthermore the hole (hole cutter provided) for the waste trap is drilled on site by the installer making avoiding joists that much simpler. Although the tray provides great thermal and acoustic insulation it is not structural so it will require to be supported throughout its entirety. The Trays are trim-able and can be cut down to a specific size or to avoid corners or match uneven walls or irregular angles.

The 900 mm x 900 mm shower base is 20 mm thick and is designed to be tiled over, providing level access into the shower without a step up. The shower base is produced from XPS foam and re-enforced on both sides with a fibreglass mesh and coated with a flexible cement. This surface is ready to tile onto. It's lightweight and flexible enough to absorb movement within the structural floor.

The shower base has a machined slope cut into it, providing a 4 way fall from each corner to the drain. The XPS foam has great acoustic properties and therefore is an excellent choice for showers here in the UK, when you can generally hear everything that's going on upstairs!

It can be easily trimmed if necessary, say around pipes or other obstacles, or if you are fitting a shower that is not quite the size of the tray. The height of the drain is 10mm, however this can be extended to 17mm using the extension provided.

The 1000 mm x 1500 mm shower base is 20 mm thick and is designed to be tiled over, providing level access into the shower without a step up. The shower base is produced from XPS foam and re-enforced on both sides with a fibreglass mesh and coated with a flexible cement. This surface is ready to tile onto. It's lightweight and flexible enough to absorb movement within the structural floor.

The shower base has a machined slope cut into it, providing a 4 way fall from each corner to the drain. The drain is offset from the centre of the tray, creating a shower zone to one end of the tray. While leaving the other end is more of a walkway or entrance to the shower. This allows for the entrance to still have a gradual slope for water to flow back toward the drain.

The XPS foam has great acoustic properties and therefore is an excellent choice for showers here in the UK, when you can generally hear everything that's going on upstairs! It can be easily trimmed if necessary, say around pipes or other obstacles, or if you are fitting a shower that is not quite the size of the tray. The height of the drain is 10mm, however this can be extended to 17mm using the extension provided.

The Top Tier wet room kit walk-in shower tray, measuring 1000 x 1500 mm, represents a standard former size. Engineered to be low level, it provides generous shower space while maintaining remarkable versatility, compatible with various shower screens and doors. Its square shape allows for placement in any part of the room, whether neatly tucked into a corner or positioned elsewhere, offering flexibility in room layout.

Each Tray's Advanced 3 piece drain offers plenty of flexibility and safety as well. The integrated plastic channel is factory installed into the tray assuring a water tight seal and allowing for the waste trap to be connected anywhere along the channel. The 304 grade stainless steel frame and cover make up the remaining parts of the drain. They are available in a variety of PVD coated colours and finishes. The frame is height adjustable to match the finished floor height. It also offers secondary drainage in case water were to ever penetrate the floor covering it will find its way to the drain. The cover itself is reversible, allowing you to either leave it right side up for a stainless steel finish to the cover or flipping it over and tiling inside for a tiled finish.

These XPS foam Trays have a Two-Way double slope machine cut into with an estimated 1-2% fall. The bottom side of the tray is level and the integrated channel does not protrude below the tray allowing for both timber and concrete floor installation. Furthermore the hole (hole cutter provided) for the waste trap is drilled on site by the installer making avoiding joists that much simpler. Although the tray provides great thermal and acoustic insulation it is not structural so it will require to be supported throughout its entirety. The Trays are trim-able and can be cut down to a specific size or to avoid corners or match uneven walls or irregular angles.

The 800 mm x 1500 mm shower base is 30 mm thick and is designed to be tiled over, providing level access into the shower without a step up. The shower base is produced from XPS foam and re-enforced on both sides with a fibreglass mesh and coated with a flexible cement. This surface is ready to tile onto. It's lightweight and flexible enough to absorb movement within the structural floor.

The XPS foam has great acoustic properties and therefore is an excellent choice for showers here in the UK, when you can generally hear everything that's going on upstairs! It can be easily trimmed if necessary, say around pipes or other obstacles, or if you are fitting a shower that is not quite the size of the tray.

The shower base has a machined slope cut into it, providing a 4 way fall from each corner to the drain. The enveloped shaped pattern helps guide the water toward the channel, eliminating the need to create fall on your own.

The 900 mm x 1400 mm shower base is 20 mm thick and is designed to be tiled over, providing level access into the shower without a step up. The shower base is produced from XPS foam and re-enforced on both sides with a fibreglass mesh and coated with a flexible cement. This surface is ready to tile onto. It's lightweight and flexible enough to absorb movement within the structural floor.

The shower base has a machined slope cut into it, providing a 4 way fall from each corner to the drain. The drain is offset from the centre of the tray, creating a shower zone to one end of the tray. While leaving the other end is more of a walkway or entrance to the shower. This allows for the entrance to still have a gradual slope for water to flow back toward the drain.

The XPS foam has great acoustic properties and therefore is an excellent choice for showers here in the UK, when you can generally hear everything that's going on upstairs! It can be easily trimmed if necessary, say around pipes or other obstacles, or if you are fitting a shower that is not quite the size of the tray. The height of the drain is 10mm, however this can be extended to 17mm using the extension provided.

The wet room shower former, measuring 900 x 1600 mm, stands as one of the largest tray bases available in our store. If you notice unused space in your bathroom and aspire to add that extra bathroom you've always desired, this spacious walk-in shower tray is an ideal choice. It not only provides ample room but also imparts a warm and luxurious feeling, enhancing your daily rituals with the pleasure of beginning and ending your day in a beautiful setting.

Each Tray's Advanced 3 piece drain offers plenty of flexibility and safety as well. The integrated plastic channel is factory installed into the tray assuring a water tight seal and allowing for the waste trap to be connected anywhere along the channel. The 304 grade stainless steel frame and cover make up the remaining parts of the drain. They are available in a variety of PVD coated colours and finishes. The frame is height adjustable to match the finished floor height. It also offers secondary drainage in case water were to ever penetrate the floor covering it will find its way to the drain. The cover itself is reversible, allowing you to either leave it right side up for a stainless steel finish to the cover or flipping it over and tiling inside for a tiled finish.

These XPS foam Trays have a One-Way single slope machine cut into with an estimated 1-2% fall. The bottom side of the tray is level and the integrated channel does not protrude below the tray allowing for both timber and concrete floor installation. Furthermore the hole (hole cutter provided) for the waste trap is drilled on site by the installer making avoiding joists that much simpler. Although the tray provides great thermal and acoustic insulation it is not structural so it will require to be supported throughout its entirety. The Trays are trim-able and can be cut down to a specific size or to avoid corners or match uneven walls or irregular angles.

The 1000 mm x 1000 mm shower base is 20 mm thick and is designed to be tiled over, providing level access into the shower without a step up. The shower base is produced from XPS foam and re-enforced on both sides with a fibreglass mesh and coated with a flexible cement. This surface is ready to tile onto. It's lightweight and flexible enough to absorb movement within the structural floor.

The shower base has a machined slope cut into it, providing a 4 way fall from each corner to the drain. The XPS foam has great acoustic properties and therefore is an excellent choice for showers here in the UK, when you can generally hear everything that's going on upstairs!

It can be easily trimmed if necessary, say around pipes or other obstacles, or if you are fitting a shower that is not quite the size of the tray. The height of the drain is 10mm, however this can be extended to 17mm using the extension provided.

The largest square shower tray, measuring 1200 x 1200 mm, accommodates larger shower areas and ensures a comfortable and easily accessible shower experience. While this size kit may not be suitable for the smallest bathrooms, it features an integrated, elongated drain that offers a modern aesthetic. With the floor appearing as a single expanse and only a drainage hole visible, it creates a seamless look that enhances the feeling of space in the bathroom.

Each Tray's Advanced 3 piece drain offers plenty of flexibility and safety as well. The integrated plastic channel is factory installed into the tray assuring a water tight seal and allowing for the waste trap to be connected anywhere along the channel. The 304 grade stainless steel frame and cover make up the remaining parts of the drain. They are available in a variety of PVD coated colours and finishes. The frame is height adjustable to match the finished floor height. It also offers secondary drainage in case water were to ever penetrate the floor covering it will find its way to the drain. The cover itself is reversible, allowing you to either leave it right side up for a stainless steel finish to the cover or flipping it over and tiling inside for a tiled finish.

These XPS foam Trays have a One-Way single slope machine cut into with an estimated 1-2% fall. The bottom side of the tray is level and the integrated channel does not protrude below the tray allowing for both timber and concrete floor installation. Furthermore the hole (hole cutter provided) for the waste trap is drilled on site by the installer making avoiding joists that much simpler. Although the tray provides great thermal and acoustic insulation it is not structural so it will require to be supported throughout its entirety. The Trays are trim-able and can be cut down to a specific size or to avoid corners or match uneven walls or irregular angles.

The 900 mm x 1200 mm shower base is 20 mm thick and is designed to be tiled over, providing level access into the shower without a step up. The shower base is produced from XPS foam and re-enforced on both sides with a fibreglass mesh and coated with a flexible cement. This surface is ready to tile onto. It's lightweight and flexible enough to absorb movement within the structural floor.

The shower base has a machined slope cut into it, providing a 4 way fall from each corner to the drain. The XPS foam has great acoustic properties and therefore is an excellent choice for showers here in the UK, when you can generally hear everything that's going on upstairs!

It can be easily trimmed if necessary, say around pipes or other obstacles, or if you are fitting a shower that is not quite the size of the tray. The height of the drain is 10mm, however this can be extended to 17mm using the extension provided

A different variant on the popular size as it offers the drain along the long 1500mm side. The drain on this tray is located 150mm from the edge of the tray and is 600mm long. Great option for a “his and hers” shower or one that has fixtures along the long side of the shower. Our Wet Room Shower Trays with Linear drains for tiled floors are the most versatile shower former you will find. They come with an integrated 600mm linear drain and are available in various sizes with different drain positions.

Each Tray's Advanced 3 piece drain offers plenty of flexibility and safety as well. The integrated plastic channel is factory installed into the tray assuring a water tight seal and allowing for the waste trap to be connected anywhere along the channel. The 304 grade stainless steel frame and cover make up the remaining parts of the drain. They are available in a variety of PVD coated colours and finishes. The frame is height adjustable to match the finished floor height. It also offers secondary drainage in case water were to ever penetrate the floor covering it will find its way to the drain. The cover itself is reversible, allowing you to either leave it right side up for a stainless steel finish to the cover or flipping it over and tiling inside for a tiled finish.

These XPS foam Trays have a 4 way slope machine cut into with an estimated 1-2% gradient fall. The bottom side of the tray is level and the integrated channel does not protrude below the tray allowing for both timber and concrete floor installation. Furthermore the hole (hole cutter provided) for the waste trap is drilled on site by the installer making avoiding joists that much simpler. Although the tray provides great thermal and acoustic insulation it is not structural so it will require to be supported throughout its entirety. The Trays are trim-able and can be cut down to a specific size or to avoid corners or match uneven walls or irregular angles.

The WetroomStop Linear Clamp Tray 800 x 1200 mm, available in 3 thicknesses, is a is a wet room tray for vinyl floors. It comes with an integrated drain that has a clamping mechanism which allows it to secure the edges of the vinyl sheet around the drain.

The tray is made of XPS foam, which is lightweight but durable and offers insulation properties. It is reinforced with fibreglass mesh and cement based glue from both sides. It also has a waterproof membrane on the top side for added protection.The tray can also be trimmed down if required to fit a specific dimension.

The tray comes as a complete set, with a brushed stainless steel cover that is available in a variety of styles. A McAlpine HC26-50 waste trap with 1.5’’ size outlet, and the optional WetroomStop Waterproofing Kit.

This WetroomStop Linear Clamp Tray 800 x 1200 mm is one of the more popular wet room tray sizes in our store. The 800 mm width is suitable for installation where space is limited, but at the same time 1200 mm length offers plenty of space for a comfortable sloped entrance.

The 900 mm x 1850 mm shower base is 20 mm thick and is designed to be tiled over, providing level access into the shower without a step up. The shower base is produced from XPS foam and re-enforced on both sides with a fibreglass mesh and coated with a flexible cement. This surface is ready to tile onto. It's lightweight and flexible enough to absorb movement within the structural floor.

The shower base has a machined slope cut into it, providing a 4 way fall from each corner to the drain. The drain is offset from the centre of the tray, creating a shower zone to one end of the tray. While leaving the other end is more of a walkway or entrance to the shower. This allows for the entrance to still have a gradual slope for water to flow back toward the drain.

The XPS foam has great acoustic properties and therefore is an excellent choice for showers here in the UK, when you can generally hear everything that's going on upstairs! It can be easily trimmed if necessary, say around pipes or other obstacles, or if you are fitting a shower that is not quite the size of the tray. The height of the drain is 10mm, however this can be extended to 17mm using the extension provided.

The Top Tier wet room kit walk-in shower tray, sized at 900 x 1400 mm, represents a typical former size. Designed to be low level, it provides ample shower space while offering remarkable versatility, compatible with various shower screens and doors. Its square shape enables placement in any part of the room, whether neatly tucked into a corner or positioned elsewhere, providing flexibility in room layout.

Each Tray's Advanced 3 piece drain offers plenty of flexibility and safety as well. The integrated plastic channel is factory installed into the tray assuring a water tight seal and allowing for the waste trap to be connected anywhere along the channel. The 304 grade stainless steel frame and cover make up the remaining parts of the drain. They are available in a variety of PVD coated colours and finishes. The frame is height adjustable to match the finished floor height. It also offers secondary drainage in case water were to ever penetrate the floor covering it will find its way to the drain. The cover itself is reversible, allowing you to either leave it right side up for a stainless steel finish to the cover or flipping it over and tiling inside for a tiled finish.

These XPS foam Trays have a Two-Way double slope machine cut into with an estimated 1-2% fall. The bottom side of the tray is level and the integrated channel does not protrude below the tray allowing for both timber and concrete floor installation. Furthermore the hole (hole cutter provided) for the waste trap is drilled on site by the installer making avoiding joists that much simpler. Although the tray provides great thermal and acoustic insulation it is not structural so it will require to be supported throughout its entirety. The Trays are trim-able and can be cut down to a specific size or to avoid corners or match uneven walls or irregular angles.

The WetroomStop Linear Clamp Tray 800 x 1500 mm, available in 3 thicknesses, is a is a wet room tray for vinyl floors. It comes with an integrated drain with a clamping mechanism which allows it to secure the edges of the vinyl sheet around the drain.

The tray is made of XPS foam, which is lightweight but durable and offers insulation properties. It is reinforced with fibreglass mesh and cement based glue from both sides. It also has a waterproof membrane on the top side for added protection.The tray can also be trimmed down if required to fit a specific dimension.

The tray comes as a complete set, with a brushed stainless steel cover that is available in a variety of styles. A McAlpine HC26-50 waste trap with 1.5’’ size outlet, and the optional WetroomStop Waterproofing Kit.

This WetroomStop Linear Clamp Tray 800 x 1500 mm wet room trays is one of our best selling sized trays. It allows you to create a modern and an accessible spacious shower area, where the shower area width is limited.

The 900 mm x 1200 mm shower base is 20 mm thick and is designed to be tiled over, providing level access into the shower without a step up. The shower base is produced from XPS foam and re-enforced on both sides with a fibreglass mesh and coated with a flexible cement. This surface is ready to tile onto. It's lightweight and flexible enough to absorb movement within the structural floor.

The shower base has a machined slope cut into it, providing a 4 way fall from each corner to the drain. The XPS foam has great acoustic properties and therefore is an excellent choice for showers here in the UK, when you can generally hear everything that's going on upstairs!

It can be easily trimmed if necessary, say around pipes or other obstacles, or if you are fitting a shower that is not quite the size of the tray. The height of the drain is 10mm, however this can be extended to 17mm using the extension provided.

The 1200 mm x 1200 mm shower base is 20 mm thick and is designed to be tiled over, providing level access into the shower without a step up. The shower base is produced from XPS foam and re-enforced on both sides with a fibreglass mesh and coated with a flexible cement. This surface is ready to tile onto. It's lightweight and flexible enough to absorb movement within the structural floor.

The shower base has a machined slope cut into it, providing a 4 way fall from each corner to the drain. The XPS foam has great acoustic properties and therefore is an excellent choice for showers here in the UK, when you can generally hear everything that's going on upstairs!

It can be easily trimmed if necessary, say around pipes or other obstacles, or if you are fitting a shower that is not quite the size of the tray. The height of the drain is 10mm, however this can be extended to 17mm using the extension provided.

The largest wet room kit, measuring 900 x 1850 mm, features a shower tray designed for installation in rooms with ample space. A walk-in shower flooring not only expands the bathroom area but also introduces a modern, simple, and fresh aesthetic, enhancing the attractiveness of the restroom. Moreover, it provides easy accessibility for individuals with mobility issues. The Showerlay of this size is particularly suitable for large tile formats, although it can still accommodate even small mosaic tiles if desired.

Each Tray's Advanced 3 piece drain offers plenty of flexibility and safety as well. The integrated plastic channel is factory installed into the tray assuring a water tight seal and allowing for the waste trap to be connected anywhere along the channel. The 304 grade stainless steel frame and cover make up the remaining parts of the drain. They are available in a variety of PVD coated colours and finishes. The frame is height adjustable to match the finished floor height. It also offers secondary drainage in case water were to ever penetrate the floor covering it will find its way to the drain. The cover itself is reversible, allowing you to either leave it right side up for a stainless steel finish to the cover or flipping it over and tiling inside for a tiled finish.

These XPS foam Trays have a Two-Way double slope machine cut into with an estimated 1-2% fall. The bottom side of the tray is level and the integrated channel does not protrude below the tray allowing for both timber and concrete floor installation. Furthermore the hole (hole cutter provided) for the waste trap is drilled on site by the installer making avoiding joists that much simpler. Although the tray provides great thermal and acoustic insulation it is not structural so it will require to be supported throughout its entirety. The Trays are trim-able and can be cut down to a specific size or to avoid corners or match uneven walls or irregular angles.

The 800 mm x 1500 mm shower base is 20 mm thick and is designed to be tiled over, providing level access into the shower without a step up. The shower base is produced from XPS foam and re-enforced on both sides with a fibreglass mesh and coated with a flexible cement. This surface is ready to tile onto. It's lightweight and flexible enough to absorb movement within the structural floor.

The shower base has a machined slope cut into it, providing a 4 way fall from each corner to the drain. The drain is offset from the centre of the tray, creating a shower zone to one end of the tray. While leaving the other end is more of a walkway or entrance to the shower. This allows for the entrance to still have a gradual slope for water to flow back toward the drain.

The XPS foam has great acoustic properties and therefore is an excellent choice for showers here in the UK, when you can generally hear everything that's going on upstairs! It can be easily trimmed if necessary, say around pipes or other obstacles, or if you are fitting a shower that is not quite the size of the tray. The height of the drain is 10mm, however this can be extended to 17mm using the extension provided.

Our most popular size tray, but this one offers the drain along the 1200mm side of the tray. The drain is 600mm long and is located 150mm from the edge. This is a great option for a shower that is wider than it is longer. Our Wet Room Shower Trays with Linear drains for tiled floors are the most versatile shower former you will find. They come with an integrated 600mm linear drain and are available in various sizes with different drain positions.

Each Tray's Advanced 3 piece drain offers plenty of flexibility and safety as well. The integrated plastic channel is factory installed into the tray assuring a water tight seal and allowing for the waste trap to be connected anywhere along the channel. The 304 grade stainless steel frame and cover make up the remaining parts of the drain. They are available in a variety of PVD coated colours and finishes. The frame is height adjustable to match the finished floor height. It also offers secondary drainage in case water were to ever penetrate the floor covering it will find its way to the drain. The cover itself is reversible, allowing you to either leave it right side up for a stainless steel finish to the cover or flipping it over and tiling inside for a tiled finish.

These XPS foam Trays have a 4 way slope machine cut into with an estimated 1-2% gradient fall. The bottom side of the tray is level and the integrated channel does not protrude below the tray allowing for both timber and concrete floor installation. Furthermore the hole (hole cutter provided) for the waste trap is drilled on site by the installer making avoiding joists that much simpler. Although the tray provides great thermal and acoustic insulation it is not structural so it will require to be supported throughout its entirety. The Trays are trim-able and can be cut down to a specific size or to avoid corners or match uneven walls or irregular angles.

The 900 mm x 1600 mm shower base is 20 mm thick and is designed to be tiled over, providing level access into the shower without a step up. The shower base is produced from XPS foam and re-enforced on both sides with a fibreglass mesh and coated with a flexible cement. This surface is ready to tile onto. It's lightweight and flexible enough to absorb movement within the structural floor.

The shower base has a machined slope cut into it, providing a 4 way fall from each corner to the drain. The drain is offset from the centre of the tray, creating a shower zone to one end of the tray. While leaving the other end is more of a walkway or entrance to the shower. This allows for the entrance to still have a gradual slope for water to flow back toward the drain.

The XPS foam has great acoustic properties and therefore is an excellent choice for showers here in the UK, when you can generally hear everything that's going on upstairs! It can be easily trimmed if necessary, say around pipes or other obstacles, or if you are fitting a shower that is not quite the size of the tray. The height of the drain is 10mm, however this can be extended to 17mm using the extension provided.

The 900 mm x 900 mm shower base is 30 mm thick and is designed to be tiled over, providing level access into the shower without a step up. The shower base is produced from XPS foam and re-enforced on both sides with a fibreglass mesh and coated with a flexible cement. This surface is ready to tile onto. It's lightweight and flexible enough to absorb movement within the structural floor.

The XPS foam has great acoustic properties and therefore is an excellent choice for showers here in the UK, when you can generally hear everything that's going on upstairs! It can be easily trimmed if necessary, say around pipes or other obstacles, or if you are fitting a shower that is not quite the size of the tray.

The shower base has a machined slope cut into it, providing a 4 way fall from each corner to the drain. The enveloped shaped pattern helps guide the water toward the channel, eliminating the need to create fall on your own.