Home

One of our largest trays, ensures that the whole area is sloped toward the drain and all the water is directed toward it. The 600mm linear drain is located parallel to the 1 m side. It sits 150mm from the edge. Our Wet Room Shower Trays with Linear drains for tiled floors are the most versatile shower former you will find. They come with an integrated 600mm linear drain and are available in various sizes with different drain positions.

Each Tray's Advanced 3 piece drain offers plenty of flexibility and safety as well. The integrated plastic channel is factory installed into the tray assuring a water tight seal and allowing for the waste trap to be connected anywhere along the channel. The 304 grade stainless steel frame and cover make up the remaining parts of the drain. They are available in a variety of PVD coated colours and finishes. The frame is height adjustable to match the finished floor height. It also offers secondary drainage in case water were to ever penetrate the floor covering it will find its way to the drain. The cover itself is reversible, allowing you to either leave it right side up for a stainless steel finish to the cover or flipping it over and tiling inside for a tiled finish.

These XPS foam Trays have a 4 way slope machine cut into with an estimated 1-2% gradient fall. The bottom side of the tray is level and the integrated channel does not protrude below the tray allowing for both timber and concrete floor installation. Furthermore the hole (hole cutter provided) for the waste trap is drilled on site by the installer making avoiding joists that much simpler. Although the tray provides great thermal and acoustic insulation it is not structural so it will require to be supported throughout its entirety. The Trays are trim-able and can be cut down to a specific size or to avoid corners or match uneven walls or irregular angles.

This popular size tray is an excellent option for a walk-in shower where space may be limited. The drain is located along the short end, 150mm from the edge, designating one end as the shower area and the far end as the entrance to the shower. Our Wet Room Shower Trays with Linear drains for tiled floors are the most versatile shower former you will find. They come with an integrated 600mm linear drain and are available in various sizes with different drain positions.

Each Tray's Advanced 3 piece drain offers plenty of flexibility and safety as well. The integrated plastic channel is factory installed into the tray assuring a water tight seal and allowing for the waste trap to be connected anywhere along the channel. The 304 grade stainless steel frame and cover make up the remaining parts of the drain. They are available in a variety of PVD coated colours and finishes. The frame is height adjustable to match the finished floor height. It also offers secondary drainage in case water were to ever penetrate the floor covering it will find its way to the drain. The cover itself is reversible, allowing you to either leave it right side up for a stainless steel finish to the cover or flipping it over and tiling inside for a tiled finish.

These XPS foam Trays have a 4 way slope machine cut into with an estimated 1-2% gradient fall. The bottom side of the tray is level and the integrated channel does not protrude below the tray allowing for both timber and concrete floor installation. Furthermore the hole (hole cutter provided) for the waste trap is drilled on site by the installer making avoiding joists that much simpler. Although the tray provides great thermal and acoustic insulation it is not structural so it will require to be supported throughout its entirety. The Trays are trim-able and can be cut down to a specific size or to avoid corners or match uneven walls or irregular angles.

This longer but narrow tray is a great option for a small shower with a comfortable entrance. The drain is located 150mm from the short end  while the far end of the tray still has a sloped floor. Our Wet Room Shower Trays with Linear drains for tiled floors are the most versatile shower former you will find. They come with an integrated 600mm linear drain and are available in various sizes with different drain positions.

Each Tray's Advanced 3 piece drain offers plenty of flexibility and safety as well. The integrated plastic channel is factory installed into the tray assuring a water tight seal and allowing for the waste trap to be connected anywhere along the channel. The 304 grade stainless steel frame and cover make up the remaining parts of the drain. They are available in a variety of PVD coated colours and finishes. The frame is height adjustable to match the finished floor height. It also offers secondary drainage in case water were to ever penetrate the floor covering it will find its way to the drain. The cover itself is reversible, allowing you to either leave it right side up for a stainless steel finish to the cover or flipping it over and tiling inside for a tiled finish.

These XPS foam Trays have a 4 way slope machine cut into with an estimated 1-2% gradient fall. The bottom side of the tray is level and the integrated channel does not protrude below the tray allowing for both timber and concrete floor installation. Furthermore the hole (hole cutter provided) for the waste trap is drilled on site by the installer making avoiding joists that much simpler. Although the tray provides great thermal and acoustic insulation it is not structural so it will require to be supported throughout its entirety. The Trays are trim-able and can be cut down to a specific size or to avoid corners or match uneven walls or irregular angles.

The WetroomStop Linear Clamp Tray 800 x 1200 mm, available in 3 thicknesses, is a is a wet room tray for vinyl floors. It comes with an integrated drain that has a clamping mechanism which allows it to secure the edges of the vinyl sheet around the drain.

The tray is made of XPS foam, which is lightweight but durable and offers insulation properties. It is reinforced with fibreglass mesh and cement based glue from both sides. It also has a waterproof membrane on the top side for added protection.The tray can also be trimmed down if required to fit a specific dimension.

The tray comes as a complete set, with a brushed stainless steel cover that is available in a variety of styles. A McAlpine HC26-50 waste trap with 1.5’’ size outlet, and the optional WetroomStop Waterproofing Kit.

This WetroomStop Linear Clamp Tray 800 x 1200 mm is one of the more popular wet room tray sizes in our store. The 800 mm width is suitable for installation where space is limited, but at the same time 1200 mm length offers plenty of space for a comfortable sloped entrance.

Sightly large variant from our most popular size. Provides plenty of space for showering and allows extra space for the entrance. The drain channel is 60mm long and is 150mm away from the short side of the tray. Our Wet Room Shower Trays with Linear drains for tiled floors are the most versatile shower former you will find. They come with an integrated 600mm linear drain and are available in various sizes with different drain positions.

Each Tray's Advanced 3 piece drain offers plenty of flexibility and safety as well. The integrated plastic channel is factory installed into the tray assuring a water tight seal and allowing for the waste trap to be connected anywhere along the channel. The 304 grade stainless steel frame and cover make up the remaining parts of the drain. They are available in a variety of PVD coated colours and finishes. The frame is height adjustable to match the finished floor height. It also offers secondary drainage in case water were to ever penetrate the floor covering it will find its way to the drain. The cover itself is reversible, allowing you to either leave it right side up for a stainless steel finish to the cover or flipping it over and tiling inside for a tiled finish.

These XPS foam Trays have a 4 way slope machine cut into with an estimated 1-2% gradient fall. The bottom side of the tray is level and the integrated channel does not protrude below the tray allowing for both timber and concrete floor installation. Furthermore the hole (hole cutter provided) for the waste trap is drilled on site by the installer making avoiding joists that much simpler. Although the tray provides great thermal and acoustic insulation it is not structural so it will require to be supported throughout its entirety. The Trays are trim-able and can be cut down to a specific size or to avoid corners or match uneven walls or irregular angles.

The WetroomStop Linear Clamp Tray 800 x 1200 mm, available in 3 thicknesses, is a is a wet room tray for vinyl floors. It comes with an integrated drain that has a clamping mechanism which allows it to secure the edges of the vinyl sheet around the drain.

The tray is made of XPS foam, which is lightweight but durable and offers insulation properties. It is reinforced with fibreglass mesh and cement based glue from both sides. It also has a waterproof membrane on the top side for added protection.The tray can also be trimmed down if required to fit a specific dimension.

The tray comes as a complete set, with a brushed stainless steel cover that is available in a variety of styles. A McAlpine HC26-50 waste trap with 1.5’’ size outlet, and the optional WetroomStop Waterproofing Kit.

This WetroomStop Linear Clamp Tray 800 x 1200 mm is one of the more popular wet room tray sizes in our store. The 800 mm width is suitable for installation where space is limited, but at the same time 1200 mm length offers plenty of space for a comfortable sloped entrance.

Spacious tray with longer entrance option. This 1.6 metre long tray allows you to have a wide screen without sacrificing the entrance opening. The 600mm long linear drain is located 150mm from the short side of the tray and offers a gradual slope from all sides. Our Wet Room Shower Trays with Linear drains for tiled floors are the most versatile shower former you will find. They come with an integrated 600mm linear drain and are available in various sizes with different drain positions.

Each Tray's Advanced 3 piece drain offers plenty of flexibility and safety as well. The integrated plastic channel is factory installed into the tray assuring a water tight seal and allowing for the waste trap to be connected anywhere along the channel. The 304 grade stainless steel frame and cover make up the remaining parts of the drain. They are available in a variety of PVD coated colours and finishes. The frame is height adjustable to match the finished floor height. It also offers secondary drainage in case water were to ever penetrate the floor covering it will find its way to the drain. The cover itself is reversible, allowing you to either leave it right side up for a stainless steel finish to the cover or flipping it over and tiling inside for a tiled finish.

These XPS foam Trays have a 4 way slope machine cut into with an estimated 1-2% gradient fall. The bottom side of the tray is level and the integrated channel does not protrude below the tray allowing for both timber and concrete floor installation. Furthermore the hole (hole cutter provided) for the waste trap is drilled on site by the installer making avoiding joists that much simpler. Although the tray provides great thermal and acoustic insulation it is not structural so it will require to be supported throughout its entirety. The Trays are trim-able and can be cut down to a specific size or to avoid corners or match uneven walls or irregular angles.

The WetroomStop Linear Clamp Tray 800 x 1500 mm, available in 3 thicknesses, is a is a wet room tray for vinyl floors. It comes with an integrated drain with a clamping mechanism which allows it to secure the edges of the vinyl sheet around the drain.

The tray is made of XPS foam, which is lightweight but durable and offers insulation properties. It is reinforced with fibreglass mesh and cement based glue from both sides. It also has a waterproof membrane on the top side for added protection.The tray can also be trimmed down if required to fit a specific dimension.

The tray comes as a complete set, with a brushed stainless steel cover that is available in a variety of styles. A McAlpine HC26-50 waste trap with 1.5’’ size outlet, and the optional WetroomStop Waterproofing Kit.

This WetroomStop Linear Clamp Tray 800 x 1500 mm wet room trays is one of our best selling sized trays. It allows you to create a modern and an accessible spacious shower area, where the shower area width is limited.

This tray is a great option for covering a large area of the room with a sloped floor. This will ensure that the room does not have any standing water left after it's been used. The 600mm drain at the end of the tray will collect all the water and drain it away. Our Wet Room Shower Trays with Linear drains for tiled floors are the most versatile shower former you will find. They come with an integrated 600mm linear drain and are available in various sizes with different drain positions.

Each Tray's Advanced 3 piece drain offers plenty of flexibility and safety as well. The integrated plastic channel is factory installed into the tray assuring a water tight seal and allowing for the waste trap to be connected anywhere along the channel. The 304 grade stainless steel frame and cover make up the remaining parts of the drain. They are available in a variety of PVD coated colours and finishes. The frame is height adjustable to match the finished floor height. It also offers secondary drainage in case water were to ever penetrate the floor covering it will find its way to the drain. The cover itself is reversible, allowing you to either leave it right side up for a stainless steel finish to the cover or flipping it over and tiling inside for a tiled finish.

These XPS foam Trays have a 4 way slope machine cut into with an estimated 1-2% gradient fall. The bottom side of the tray is level and the integrated channel does not protrude below the tray allowing for both timber and concrete floor installation. Furthermore the hole (hole cutter provided) for the waste trap is drilled on site by the installer making avoiding joists that much simpler. Although the tray provides great thermal and acoustic insulation it is not structural so it will require to be supported throughout its entirety. The Trays are trim-able and can be cut down to a specific size or to avoid corners or match uneven walls or irregular angles.

The WetroomStop Linear Clamp Tray 800 x 1500 mm, available in 3 thicknesses, is a is a wet room tray for vinyl floors. It comes with an integrated drain with a clamping mechanism which allows it to secure the edges of the vinyl sheet around the drain.

The tray is made of XPS foam, which is lightweight but durable and offers insulation properties. It is reinforced with fibreglass mesh and cement based glue from both sides. It also has a waterproof membrane on the top side for added protection.The tray can also be trimmed down if required to fit a specific dimension.

The tray comes as a complete set, with a brushed stainless steel cover that is available in a variety of styles. A McAlpine HC26-50 waste trap with 1.5’’ size outlet, and the optional WetroomStop Waterproofing Kit.

This WetroomStop Linear Clamp Tray 800 x 1500 mm wet room trays is one of our best selling sized trays. It allows you to create a modern and an accessible spacious shower area, where the shower area width is limited.

The longest tray in our series. This tray is twice as long as it is wide and is a great option when considering having the entire floor of a small wet room contain a slope toward the drain. The tray's slope is very gradual however it's sufficient enough that the water from the entire tray will find its way to the drain. Our Wet Room Shower Trays with Linear drains for tiled floors are the most versatile shower former you will find. They come with an integrated 600mm linear drain and are available in various sizes with different drain positions.

Each Tray's Advanced 3 piece drain offers plenty of flexibility and safety as well. The integrated plastic channel is factory installed into the tray assuring a water tight seal and allowing for the waste trap to be connected anywhere along the channel. The 304 grade stainless steel frame and cover make up the remaining parts of the drain. They are available in a variety of PVD coated colours and finishes. The frame is height adjustable to match the finished floor height. It also offers secondary drainage in case water were to ever penetrate the floor covering it will find its way to the drain. The cover itself is reversible, allowing you to either leave it right side up for a stainless steel finish to the cover or flipping it over and tiling inside for a tiled finish.

These XPS foam Trays have a 4 way slope machine cut into with an estimated 1-2% gradient fall. The bottom side of the tray is level and the integrated channel does not protrude below the tray allowing for both timber and concrete floor installation. Furthermore the hole (hole cutter provided) for the waste trap is drilled on site by the installer making avoiding joists that much simpler. Although the tray provides great thermal and acoustic insulation it is not structural so it will require to be supported throughout its entirety. The Trays are trim-able and can be cut down to a specific size or to avoid corners or match uneven walls or irregular angles.

The WetroomStop Linear Clamp Tray 800 x 800 mm is a wet room tray designed specifically for vinyl floor coverings. It comes with an integrated clamp drain that has a mechanism which allows it to secure the edges of the vinyl sheet around the drain.

The tray is made of XPS foam, which is lightweight but durable and offers insulation properties. It is reinforced with fibreglass mesh and cement based glue from both sides. It also has a waterproof membrane on the top side for added protection.The tray can also be trimmed down if required to fit a specific dimension.

The tray comes as a complete set, with a brushed stainless steel cover that is available in a variety of styles. A McAlpine HC26-50 waste trap with 1.5’’ size outlet, and the optional WetroomStop Waterproofing Kit.

This WetroomStop Linear Clamp Tray 800 x 800 mm tray is the smallest of our standard sizes, making it ideal for even the smallest of spaces. This wet room tray allows you to achieve a barrier free easy access shower in small rooms or conversions.

A different variant on the popular size as it offers the drain along the long 1500mm side. The drain on this tray is located 150mm from the edge of the tray and is 600mm long. Great option for a “his and hers” shower or one that has fixtures along the long side of the shower. Our Wet Room Shower Trays with Linear drains for tiled floors are the most versatile shower former you will find. They come with an integrated 600mm linear drain and are available in various sizes with different drain positions.

Each Tray's Advanced 3 piece drain offers plenty of flexibility and safety as well. The integrated plastic channel is factory installed into the tray assuring a water tight seal and allowing for the waste trap to be connected anywhere along the channel. The 304 grade stainless steel frame and cover make up the remaining parts of the drain. They are available in a variety of PVD coated colours and finishes. The frame is height adjustable to match the finished floor height. It also offers secondary drainage in case water were to ever penetrate the floor covering it will find its way to the drain. The cover itself is reversible, allowing you to either leave it right side up for a stainless steel finish to the cover or flipping it over and tiling inside for a tiled finish.

These XPS foam Trays have a 4 way slope machine cut into with an estimated 1-2% gradient fall. The bottom side of the tray is level and the integrated channel does not protrude below the tray allowing for both timber and concrete floor installation. Furthermore the hole (hole cutter provided) for the waste trap is drilled on site by the installer making avoiding joists that much simpler. Although the tray provides great thermal and acoustic insulation it is not structural so it will require to be supported throughout its entirety. The Trays are trim-able and can be cut down to a specific size or to avoid corners or match uneven walls or irregular angles.

The WetroomStop Linear Clamp Tray 800 x 800 mm is a wet room tray designed specifically for vinyl floor coverings. It comes with an integrated clamp drain that has a mechanism which allows it to secure the edges of the vinyl sheet around the drain.

The tray is made of XPS foam, which is lightweight but durable and offers insulation properties. It is reinforced with fibreglass mesh and cement based glue from both sides. It also has a waterproof membrane on the top side for added protection.The tray can also be trimmed down if required to fit a specific dimension.

The tray comes as a complete set, with a brushed stainless steel cover that is available in a variety of styles. A McAlpine HC26-50 waste trap with 1.5’’ size outlet, and the optional WetroomStop Waterproofing Kit.

This WetroomStop Linear Clamp Tray 800 x 800 mm tray is the smallest of our standard sizes, making it ideal for even the smallest of spaces. This wet room tray allows you to achieve a barrier free easy access shower in small rooms or conversions.

Our most popular size tray, but this one offers the drain along the 1200mm side of the tray. The drain is 600mm long and is located 150mm from the edge. This is a great option for a shower that is wider than it is longer. Our Wet Room Shower Trays with Linear drains for tiled floors are the most versatile shower former you will find. They come with an integrated 600mm linear drain and are available in various sizes with different drain positions.

Each Tray's Advanced 3 piece drain offers plenty of flexibility and safety as well. The integrated plastic channel is factory installed into the tray assuring a water tight seal and allowing for the waste trap to be connected anywhere along the channel. The 304 grade stainless steel frame and cover make up the remaining parts of the drain. They are available in a variety of PVD coated colours and finishes. The frame is height adjustable to match the finished floor height. It also offers secondary drainage in case water were to ever penetrate the floor covering it will find its way to the drain. The cover itself is reversible, allowing you to either leave it right side up for a stainless steel finish to the cover or flipping it over and tiling inside for a tiled finish.

These XPS foam Trays have a 4 way slope machine cut into with an estimated 1-2% gradient fall. The bottom side of the tray is level and the integrated channel does not protrude below the tray allowing for both timber and concrete floor installation. Furthermore the hole (hole cutter provided) for the waste trap is drilled on site by the installer making avoiding joists that much simpler. Although the tray provides great thermal and acoustic insulation it is not structural so it will require to be supported throughout its entirety. The Trays are trim-able and can be cut down to a specific size or to avoid corners or match uneven walls or irregular angles.

The WetroomStop Linear Clamp Tray 800 x 800 mm is a wet room tray designed specifically for vinyl floor coverings. It comes with an integrated clamp drain that has a mechanism which allows it to secure the edges of the vinyl sheet around the drain.

The tray is made of XPS foam, which is lightweight but durable and offers insulation properties. It is reinforced with fibreglass mesh and cement based glue from both sides. It also has a waterproof membrane on the top side for added protection.The tray can also be trimmed down if required to fit a specific dimension.

The tray comes as a complete set, with a brushed stainless steel cover that is available in a variety of styles. A McAlpine HC26-50 waste trap with 1.5’’ size outlet, and the optional WetroomStop Waterproofing Kit.

This WetroomStop Linear Clamp Tray 800 x 800 mm tray is the smallest of our standard sizes, making it ideal for even the smallest of spaces. This wet room tray allows you to achieve a barrier free easy access shower in small rooms or conversions.

This tray has the drain along the long 1700mm side of the tray. It is perfect for a “his and hers” shower or a shower that has a walk through with entrances from both sides. The 600 mm drain is centred on the tray along the long side of it. It is located 150mm from the edge. Our Wet Room Shower Trays with Linear drains for tiled floors are the most versatile shower former you will find. They come with an integrated 600mm linear drain and are available in various sizes with different drain positions.

Each Tray's Advanced 3 piece drain offers plenty of flexibility and safety as well. The integrated plastic channel is factory installed into the tray assuring a water tight seal and allowing for the waste trap to be connected anywhere along the channel. The 304 grade stainless steel frame and cover make up the remaining parts of the drain. They are available in a variety of PVD coated colours and finishes. The frame is height adjustable to match the finished floor height. It also offers secondary drainage in case water were to ever penetrate the floor covering it will find its way to the drain. The cover itself is reversible, allowing you to either leave it right side up for a stainless steel finish to the cover or flipping it over and tiling inside for a tiled finish.

These XPS foam Trays have a 4 way slope machine cut into with an estimated 1-2% gradient fall. The bottom side of the tray is level and the integrated channel does not protrude below the tray allowing for both timber and concrete floor installation. Furthermore the hole (hole cutter provided) for the waste trap is drilled on site by the installer making avoiding joists that much simpler. Although the tray provides great thermal and acoustic insulation it is not structural so it will require to be supported throughout its entirety. The Trays are trim-able and can be cut down to a specific size or to avoid corners or match uneven walls or irregular angles.

The WetroomStop Linear Clamp Tray 900 x 1200 mm, available in 3 thicknesses, is a is a wet room tray for vinyl floors. It comes with an integrated clamp drain that has a mechanism which allows it to secure the edges of the vinyl sheet around the drain.

The tray is made of XPS foam, which is lightweight but durable and offers insulation properties. It is reinforced with fibreglass mesh and cement based glue from both sides. It also has a waterproof membrane on the top side for added protection.The tray can also be trimmed down if required to fit a specific dimension.

The tray comes as a complete set, with a brushed stainless steel cover that is available in a variety of styles. A McAlpine HC26-50 waste trap with 1.5’’ size outlet, and the optional WetroomStop Waterproofing Kit.

This WetroomStop Linear Clamp Tray 900 x 1200 mm is the best selling size in our store. The length and width complement each other giving you a sufficient sized shower area that does not require a closed cabin as the sloped floor will catch any of the water that splashes away from the shower area.

A different variant on the popular size as it offers the drain along the long 1500mm side. The drain on this tray is located 150mm from the edge of the tray and is 600mm long. Great option for a “his and hers” shower or one that has fixtures along the long side of the shower. Our Wet Room Shower Trays with Linear drains for tiled floors are the most versatile shower former you will find. They come with an integrated 600mm linear drain and are available in various sizes with different drain positions.

Each Tray's Advanced 3 piece drain offers plenty of flexibility and safety as well. The integrated plastic channel is factory installed into the tray assuring a water tight seal and allowing for the waste trap to be connected anywhere along the channel. The 304 grade stainless steel frame and cover make up the remaining parts of the drain. They are available in a variety of PVD coated colours and finishes. The frame is height adjustable to match the finished floor height. It also offers secondary drainage in case water were to ever penetrate the floor covering it will find its way to the drain. The cover itself is reversible, allowing you to either leave it right side up for a stainless steel finish to the cover or flipping it over and tiling inside for a tiled finish.

These XPS foam Trays have a 4 way slope machine cut into with an estimated 1-2% gradient fall. The bottom side of the tray is level and the integrated channel does not protrude below the tray allowing for both timber and concrete floor installation. Furthermore the hole (hole cutter provided) for the waste trap is drilled on site by the installer making avoiding joists that much simpler. Although the tray provides great thermal and acoustic insulation it is not structural so it will require to be supported throughout its entirety. The Trays are trim-able and can be cut down to a specific size or to avoid corners or match uneven walls or irregular angles.

The WetroomStop Linear Clamp Tray 900 x 1200 mm, available in 3 thicknesses, is a is a wet room tray for vinyl floors. It comes with an integrated clamp drain that has a mechanism which allows it to secure the edges of the vinyl sheet around the drain.

The tray is made of XPS foam, which is lightweight but durable and offers insulation properties. It is reinforced with fibreglass mesh and cement based glue from both sides. It also has a waterproof membrane on the top side for added protection.The tray can also be trimmed down if required to fit a specific dimension.

The tray comes as a complete set, with a brushed stainless steel cover that is available in a variety of styles. A McAlpine HC26-50 waste trap with 1.5’’ size outlet, and the optional WetroomStop Waterproofing Kit.

This WetroomStop Linear Clamp Tray 900 x 1200 mm is the best selling size in our store. The length and width complement each other giving you a sufficient sized shower area that does not require a closed cabin as the sloped floor will catch any of the water that splashes away from the shower area.

Our most popular size tray, but this one offers the drain along the 1200mm side of the tray. The drain is 600mm long and is located 150mm from the edge. This is a great option for a shower that is wider than it is longer. Our Wet Room Shower Trays with Linear drains for tiled floors are the most versatile shower former you will find. They come with an integrated 600mm linear drain and are available in various sizes with different drain positions.

Each Tray's Advanced 3 piece drain offers plenty of flexibility and safety as well. The integrated plastic channel is factory installed into the tray assuring a water tight seal and allowing for the waste trap to be connected anywhere along the channel. The 304 grade stainless steel frame and cover make up the remaining parts of the drain. They are available in a variety of PVD coated colours and finishes. The frame is height adjustable to match the finished floor height. It also offers secondary drainage in case water were to ever penetrate the floor covering it will find its way to the drain. The cover itself is reversible, allowing you to either leave it right side up for a stainless steel finish to the cover or flipping it over and tiling inside for a tiled finish.

These XPS foam Trays have a 4 way slope machine cut into with an estimated 1-2% gradient fall. The bottom side of the tray is level and the integrated channel does not protrude below the tray allowing for both timber and concrete floor installation. Furthermore the hole (hole cutter provided) for the waste trap is drilled on site by the installer making avoiding joists that much simpler. Although the tray provides great thermal and acoustic insulation it is not structural so it will require to be supported throughout its entirety. The Trays are trim-able and can be cut down to a specific size or to avoid corners or match uneven walls or irregular angles.

The WetroomStop Linear Clamp Tray 900 x 1200 mm, available in 3 thicknesses, is a is a wet room tray for vinyl floors. It comes with an integrated clamp drain that has a mechanism which allows it to secure the edges of the vinyl sheet around the drain.

The tray is made of XPS foam, which is lightweight but durable and offers insulation properties. It is reinforced with fibreglass mesh and cement based glue from both sides. It also has a waterproof membrane on the top side for added protection.The tray can also be trimmed down if required to fit a specific dimension.

The tray comes as a complete set, with a brushed stainless steel cover that is available in a variety of styles. A McAlpine HC26-50 waste trap with 1.5’’ size outlet, and the optional WetroomStop Waterproofing Kit.

This WetroomStop Linear Clamp Tray 900 x 1200 mm is the best selling size in our store. The length and width complement each other giving you a sufficient sized shower area that does not require a closed cabin as the sloped floor will catch any of the water that splashes away from the shower area.