Wet Room Trays for Tiled Floor

The 800 mm x 1500 mm shower base is 30 mm thick and is designed to be tiled over, providing level access into the shower without a step up. The shower base is produced from XPS foam and re-enforced on both sides with a fibreglass mesh and coated with a flexible cement. This surface is ready to tile onto. It's lightweight and flexible enough to absorb movement within the structural floor.

The XPS foam has great acoustic properties and therefore is an excellent choice for showers here in the UK, when you can generally hear everything that's going on upstairs! It can be easily trimmed if necessary, say around pipes or other obstacles, or if you are fitting a shower that is not quite the size of the tray.

The shower base has a machined slope cut into it, providing a 4 way fall from each corner to the drain. The enveloped shaped pattern helps guide the water toward the channel, eliminating the need to create fall on your own.

The 900 mm x 1700 mm shower base is 20 mm thick and is designed to be tiled over, providing level access into the shower without a step up. The shower base is produced from XPS foam and re-enforced on both sides with a fibreglass mesh and coated with a flexible cement. This surface is ready to tile onto. It's lightweight and flexible enough to absorb movement within the structural floor.

The shower base has a machined slope cut into it, providing a 4 way fall from each corner to the drain. The drain is offset from the centre of the tray, creating a shower zone to one end of the tray. While leaving the other end is more of a walkway or entrance to the shower. This allows for the entrance to still have a gradual slope for water to flow back toward the drain.

The XPS foam has great acoustic properties and therefore is an excellent choice for showers here in the UK, when you can generally hear everything that's going on upstairs! It can be easily trimmed if necessary, say around pipes or other obstacles, or if you are fitting a shower that is not quite the size of the tray. The height of the drain is 10mm, however this can be extended to 17mm using the extension provided.

The 900 mm x 1400 mm shower base is 30 mm thick and is designed to be tiled over, providing level access into the shower without a step up. The shower base is produced from XPS foam and re-enforced on both sides with a fibreglass mesh and coated with a flexible cement. This surface is ready to tile onto. It's lightweight and flexible enough to absorb movement within the structural floor.

The XPS foam has great acoustic properties and therefore is an excellent choice for showers here in the UK, when you can generally hear everything that's going on upstairs! It can be easily trimmed if necessary, say around pipes or other obstacles, or if you are fitting a shower that is not quite the size of the tray.

The shower base has a machined slope cut into it, providing a 4 way fall from each corner to the drain. The enveloped shaped pattern helps guide the water toward the channel, eliminating the need to create fall on your own.

The 900 mm x 1850 mm shower base is 20 mm thick and is designed to be tiled over, providing level access into the shower without a step up. The shower base is produced from XPS foam and re-enforced on both sides with a fibreglass mesh and coated with a flexible cement. This surface is ready to tile onto. It's lightweight and flexible enough to absorb movement within the structural floor.

The shower base has a machined slope cut into it, providing a 4 way fall from each corner to the drain. The drain is offset from the centre of the tray, creating a shower zone to one end of the tray. While leaving the other end is more of a walkway or entrance to the shower. This allows for the entrance to still have a gradual slope for water to flow back toward the drain.

The XPS foam has great acoustic properties and therefore is an excellent choice for showers here in the UK, when you can generally hear everything that's going on upstairs! It can be easily trimmed if necessary, say around pipes or other obstacles, or if you are fitting a shower that is not quite the size of the tray. The height of the drain is 10mm, however this can be extended to 17mm using the extension provided.

The 1000 mm x 1000 mm shower base is 20 mm thick and is designed to be tiled over, providing level access into the shower without a step up. The shower base is produced from XPS foam and re-enforced on both sides with a fibreglass mesh and coated with a flexible cement. This surface is ready to tile onto. It's lightweight and flexible enough to absorb movement within the structural floor.

The shower base has a machined slope cut into it, providing a 4 way fall from each corner to the drain. The XPS foam has great acoustic properties and therefore is an excellent choice for showers here in the UK, when you can generally hear everything that's going on upstairs!

It can be easily trimmed if necessary, say around pipes or other obstacles, or if you are fitting a shower that is not quite the size of the tray. The height of the drain is 10mm, however this can be extended to 17mm using the extension provided.

The 900 mm x 1600 mm shower base is 30 mm thick and is designed to be tiled over, providing level access into the shower without a step up. The shower base is produced from XPS foam and re-enforced on both sides with a fibreglass mesh and coated with a flexible cement. This surface is ready to tile onto. It's lightweight and flexible enough to absorb movement within the structural floor.

The XPS foam has great acoustic properties and therefore is an excellent choice for showers here in the UK, when you can generally hear everything that's going on upstairs! It can be easily trimmed if necessary, say around pipes or other obstacles, or if you are fitting a shower that is not quite the size of the tray.

The shower base has a machined slope cut into it, providing a 4 way fall from each corner to the drain. The enveloped shaped pattern helps guide the water toward the channel, eliminating the need to create fall on your own.

The 900 mm x 1200 mm shower base is 20 mm thick and is designed to be tiled over, providing level access into the shower without a step up. The shower base is produced from XPS foam and re-enforced on both sides with a fibreglass mesh and coated with a flexible cement. This surface is ready to tile onto. It's lightweight and flexible enough to absorb movement within the structural floor.

The shower base has a machined slope cut into it, providing a 4 way fall from each corner to the drain. The XPS foam has great acoustic properties and therefore is an excellent choice for showers here in the UK, when you can generally hear everything that's going on upstairs!

It can be easily trimmed if necessary, say around pipes or other obstacles, or if you are fitting a shower that is not quite the size of the tray. The height of the drain is 10mm, however this can be extended to 17mm using the extension provided

The 900 mm x 1700 mm shower base is 30 mm thick and is designed to be tiled over, providing level access into the shower without a step up. The shower base is produced from XPS foam and re-enforced on both sides with a fibreglass mesh and coated with a flexible cement. This surface is ready to tile onto. It's lightweight and flexible enough to absorb movement within the structural floor.

The XPS foam has great acoustic properties and therefore is an excellent choice for showers here in the UK, when you can generally hear everything that's going on upstairs! It can be easily trimmed if necessary, say around pipes or other obstacles, or if you are fitting a shower that is not quite the size of the tray.

The shower base has a machined slope cut into it, providing a 4 way fall from each corner to the drain. The enveloped shaped pattern helps guide the water toward the channel, eliminating the need to create fall on your own.

The 900 mm x 1850 mm shower base is 30 mm thick and is designed to be tiled over, providing level access into the shower without a step up. The shower base is produced from XPS foam and re-enforced on both sides with a fibreglass mesh and coated with a flexible cement. This surface is ready to tile onto. It's lightweight and flexible enough to absorb movement within the structural floor.

The XPS foam has great acoustic properties and therefore is an excellent choice for showers here in the UK, when you can generally hear everything that's going on upstairs! It can be easily trimmed if necessary, say around pipes or other obstacles, or if you are fitting a shower that is not quite the size of the tray.

The shower base has a machined slope cut into it, providing a 4 way fall from each corner to the drain. The enveloped shaped pattern helps guide the water toward the channel, eliminating the need to create fall on your own.

Our most popular size tray, but this one offers the drain along the 1200mm side of the tray. The drain is 600mm long and is located 150mm from the edge. This is a great option for a shower that is wider than it is longer. Our Wet Room Shower Trays with Linear drains for tiled floors are the most versatile shower former you will find. They come with an integrated 600mm linear drain and are available in various sizes with different drain positions.

Each Tray's Advanced 3 piece drain offers plenty of flexibility and safety as well. The integrated plastic channel is factory installed into the tray assuring a water tight seal and allowing for the waste trap to be connected anywhere along the channel. The 304 grade stainless steel frame and cover make up the remaining parts of the drain. They are available in a variety of PVD coated colours and finishes. The frame is height adjustable to match the finished floor height. It also offers secondary drainage in case water were to ever penetrate the floor covering it will find its way to the drain. The cover itself is reversible, allowing you to either leave it right side up for a stainless steel finish to the cover or flipping it over and tiling inside for a tiled finish.

These XPS foam Trays have a 4 way slope machine cut into with an estimated 1-2% gradient fall. The bottom side of the tray is level and the integrated channel does not protrude below the tray allowing for both timber and concrete floor installation. Furthermore the hole (hole cutter provided) for the waste trap is drilled on site by the installer making avoiding joists that much simpler. Although the tray provides great thermal and acoustic insulation it is not structural so it will require to be supported throughout its entirety. The Trays are trim-able and can be cut down to a specific size or to avoid corners or match uneven walls or irregular angles.

Our most popular size tray, but this one offers the drain along the 1700mm side of the tray. The drain is 600mm long and is located 150mm from the edge. This is a great option for a shower that is wider than it is longer. Our Wet Room Shower Trays with Linear drains for tiled floors are the most versatile shower former you will find. They come with an integrated 600mm linear drain and are available in various sizes with different drain positions.

Each Tray's Advanced 3 piece drain offers plenty of flexibility and safety as well. The integrated plastic channel is factory installed into the tray assuring a water tight seal and allowing for the waste trap to be connected anywhere along the channel. The 304 grade stainless steel frame and cover make up the remaining parts of the drain. They are available in a variety of PVD coated colours and finishes. The frame is height adjustable to match the finished floor height. It also offers secondary drainage in case water were to ever penetrate the floor covering it will find its way to the drain. The cover itself is reversible, allowing you to either leave it right side up for a stainless steel finish to the cover or flipping it over and tiling inside for a tiled finish.

These XPS foam Trays have a 4 way slope machine cut into with an estimated 1-2% gradient fall. The bottom side of the tray is level and the integrated channel does not protrude below the tray allowing for both timber and concrete floor installation. Furthermore the hole (hole cutter provided) for the waste trap is drilled on site by the installer making avoiding joists that much simpler. Although the tray provides great thermal and acoustic insulation it is not structural so it will require to be supported throughout its entirety. The Trays are trim-able and can be cut down to a specific size or to avoid corners or match uneven walls or irregular angles.

Very compact tray, square in shape, can be installed with the drain along any side. The 600mm linear drain is located 150mm for the edge of the tray and has 150mm of tray on both ends. Our Wet Room Shower Trays with Linear drains for tiled floors are the most versatile shower former you will find. They come with an integrated 600mm linear drain and are available in various sizes with different drain positions.

Each Tray's Advanced 3 piece drain offers plenty of flexibility and safety as well. The integrated plastic channel is factory installed into the tray assuring a water tight seal and allowing for the waste trap to be connected anywhere along the channel. The 304 grade stainless steel frame and cover make up the remaining parts of the drain. They are available in a variety of PVD coated colours and finishes. The frame is height adjustable to match the finished floor height. It also offers secondary drainage in case water were to ever penetrate the floor covering it will find its way to the drain. The cover itself is reversible, allowing you to either leave it right side up for a stainless steel finish to the cover or flipping it over and tiling inside for a tiled finish.

These XPS foam Trays have a 4 way slope machine cut into with an estimated 1-2% gradient fall. The bottom side of the tray is level and the integrated channel does not protrude below the tray allowing for both timber and concrete floor installation. Furthermore the hole (hole cutter provided) for the waste trap is drilled on site by the installer making avoiding joists that much simpler. Although the tray provides great thermal and acoustic insulation it is not structural so it will require to be supported throughout its entirety. The Trays are trim-able and can be cut down to a specific size or to avoid corners or match uneven walls or irregular angles.

The most popular size tray. Allows ample space for showering and does not take up too much space in the room. The 600mm linear drain channel is parallel to the 900mm side and is 150mm away from the edge of the tray. Our Wet Room Shower Trays with Linear drains for tiled floors are the most versatile shower former you will find. They come with an integrated 600mm linear drain and are available in various sizes with different drain positions.

Each Tray's Advanced 3 piece drain offers plenty of flexibility and safety as well. The integrated plastic channel is factory installed into the tray assuring a water tight seal and allowing for the waste trap to be connected anywhere along the channel. The 304 grade stainless steel frame and cover make up the remaining parts of the drain. They are available in a variety of PVD coated colours and finishes. The frame is height adjustable to match the finished floor height. It also offers secondary drainage in case water were to ever penetrate the floor covering it will find its way to the drain. The cover itself is reversible, allowing you to either leave it right side up for a stainless steel finish to the cover or flipping it over and tiling inside for a tiled finish.

These XPS foam Trays have a 4 way slope machine cut into with an estimated 1-2% gradient fall. The bottom side of the tray is level and the integrated channel does not protrude below the tray allowing for both timber and concrete floor installation. Furthermore the hole (hole cutter provided) for the waste trap is drilled on site by the installer making avoiding joists that much simpler. Although the tray provides great thermal and acoustic insulation it is not structural so it will require to be supported throughout its entirety. The Trays are trim-able and can be cut down to a specific size or to avoid corners or match uneven walls or irregular angles.

Very popular size tray. Provides an excellent walk in shower size where the opening for the entrance can remain open. The drain is 600mm long and is parallel to the 900mm side. It is located 150mm from the edge of the tray. Our Wet Room Shower Trays with Linear drains for tiled floors are the most versatile shower former you will find. They come with an integrated 600mm linear drain and are available in various sizes with different drain positions.

Each Tray's Advanced 3 piece drain offers plenty of flexibility and safety as well. The integrated plastic channel is factory installed into the tray assuring a water tight seal and allowing for the waste trap to be connected anywhere along the channel. The 304 grade stainless steel frame and cover make up the remaining parts of the drain. They are available in a variety of PVD coated colours and finishes. The frame is height adjustable to match the finished floor height. It also offers secondary drainage in case water were to ever penetrate the floor covering it will find its way to the drain. The cover itself is reversible, allowing you to either leave it right side up for a stainless steel finish to the cover or flipping it over and tiling inside for a tiled finish.

These XPS foam Trays have a 4 way slope machine cut into with an estimated 1-2% gradient fall. The bottom side of the tray is level and the integrated channel does not protrude below the tray allowing for both timber and concrete floor installation. Furthermore the hole (hole cutter provided) for the waste trap is drilled on site by the installer making avoiding joists that much simpler. Although the tray provides great thermal and acoustic insulation it is not structural so it will require to be supported throughout its entirety. The Trays are trim-able and can be cut down to a specific size or to avoid corners or match uneven walls or irregular angles.

The smallest of the trays we offer. Square in shape, with the 600mm channel located 150mm from the edge of the tray and 100mm on each end. The tray can be rotated and installed with the drain along  the top or the side. Our Wet Room Shower Trays with Linear drains for tiled floors are the most versatile shower former you will find. They come with an integrated 600mm linear drain and are available in various sizes with different drain positions.

Each Tray's Advanced 3 piece drain offers plenty of flexibility and safety as well. The integrated plastic channel is factory installed into the tray assuring a water tight seal and allowing for the waste trap to be connected anywhere along the channel. The 304 grade stainless steel frame and cover make up the remaining parts of the drain. They are available in a variety of PVD coated colours and finishes. The frame is height adjustable to match the finished floor height. It also offers secondary drainage in case water were to ever penetrate the floor covering it will find its way to the drain. The cover itself is reversible, allowing you to either leave it right side up for a stainless steel finish to the cover or flipping it over and tiling inside for a tiled finish.

These XPS foam Trays have a 4 way slope machine cut into with an estimated 1-2% gradient fall. The bottom side of the tray is level and the integrated channel does not protrude below the tray allowing for both timber and concrete floor installation. Furthermore the hole (hole cutter provided) for the waste trap is drilled on site by the installer making avoiding joists that much simpler. Although the tray provides great thermal and acoustic insulation it is not structural so it will require to be supported throughout its entirety. The Trays are trim-able and can be cut down to a specific size or to avoid corners or match uneven walls or irregular angles.

This spacious square tray offers a variety of installation options. Allowing you to place the drain along whichever side you seem fit. The 600 mm linear drain is located 150mm from the edge of the tray leaving 200mm on each end. Our Wet Room Shower Trays with Linear drains for tiled floors are the most versatile shower former you will find. They come with an integrated 600mm linear drain and are available in various sizes with different drain positions.

Each Tray's Advanced 3 piece drain offers plenty of flexibility and safety as well. The integrated plastic channel is factory installed into the tray assuring a water tight seal and allowing for the waste trap to be connected anywhere along the channel. The 304 grade stainless steel frame and cover make up the remaining parts of the drain. They are available in a variety of PVD coated colours and finishes. The frame is height adjustable to match the finished floor height. It also offers secondary drainage in case water were to ever penetrate the floor covering it will find its way to the drain. The cover itself is reversible, allowing you to either leave it right side up for a stainless steel finish to the cover or flipping it over and tiling inside for a tiled finish.

These XPS foam Trays have a 4 way slope machine cut into with an estimated 1-2% gradient fall. The bottom side of the tray is level and the integrated channel does not protrude below the tray allowing for both timber and concrete floor installation. Furthermore the hole (hole cutter provided) for the waste trap is drilled on site by the installer making avoiding joists that much simpler. Although the tray provides great thermal and acoustic insulation it is not structural so it will require to be supported throughout its entirety. The Trays are trim-able and can be cut down to a specific size or to avoid corners or match uneven walls or irregular angles.

This very large tray is ideal for barrier free wetrooms. The 1.2 m by 1.2 m square shape allows you to install the drain along any side. It also leaves ample room for freedom of movement in all directions. Our Wet Room Shower Trays with Linear drains for tiled floors are the most versatile shower former you will find. They come with an integrated 600mm linear drain and are available in various sizes with different drain positions.

Each Tray's Advanced 3 piece drain offers plenty of flexibility and safety as well. The integrated plastic channel is factory installed into the tray assuring a water tight seal and allowing for the waste trap to be connected anywhere along the channel. The 304 grade stainless steel frame and cover make up the remaining parts of the drain. They are available in a variety of PVD coated colours and finishes. The frame is height adjustable to match the finished floor height. It also offers secondary drainage in case water were to ever penetrate the floor covering it will find its way to the drain. The cover itself is reversible, allowing you to either leave it right side up for a stainless steel finish to the cover or flipping it over and tiling inside for a tiled finish.

These XPS foam Trays have a 4 way slope machine cut into with an estimated 1-2% gradient fall. The bottom side of the tray is level and the integrated channel does not protrude below the tray allowing for both timber and concrete floor installation. Furthermore the hole (hole cutter provided) for the waste trap is drilled on site by the installer making avoiding joists that much simpler. Although the tray provides great thermal and acoustic insulation it is not structural so it will require to be supported throughout its entirety. The Trays are trim-able and can be cut down to a specific size or to avoid corners or match uneven walls or irregular angles.

One of our largest trays, ensures that the whole area is sloped toward the drain and all the water is directed toward it. The 600mm linear drain is located parallel to the 1 m side. It sits 150mm from the edge. Our Wet Room Shower Trays with Linear drains for tiled floors are the most versatile shower former you will find. They come with an integrated 600mm linear drain and are available in various sizes with different drain positions.

Each Tray's Advanced 3 piece drain offers plenty of flexibility and safety as well. The integrated plastic channel is factory installed into the tray assuring a water tight seal and allowing for the waste trap to be connected anywhere along the channel. The 304 grade stainless steel frame and cover make up the remaining parts of the drain. They are available in a variety of PVD coated colours and finishes. The frame is height adjustable to match the finished floor height. It also offers secondary drainage in case water were to ever penetrate the floor covering it will find its way to the drain. The cover itself is reversible, allowing you to either leave it right side up for a stainless steel finish to the cover or flipping it over and tiling inside for a tiled finish.

These XPS foam Trays have a 4 way slope machine cut into with an estimated 1-2% gradient fall. The bottom side of the tray is level and the integrated channel does not protrude below the tray allowing for both timber and concrete floor installation. Furthermore the hole (hole cutter provided) for the waste trap is drilled on site by the installer making avoiding joists that much simpler. Although the tray provides great thermal and acoustic insulation it is not structural so it will require to be supported throughout its entirety. The Trays are trim-able and can be cut down to a specific size or to avoid corners or match uneven walls or irregular angles.

This popular size tray is an excellent option for a walk-in shower where space may be limited. The drain is located along the short end, 150mm from the edge, designating one end as the shower area and the far end as the entrance to the shower. Our Wet Room Shower Trays with Linear drains for tiled floors are the most versatile shower former you will find. They come with an integrated 600mm linear drain and are available in various sizes with different drain positions.

Each Tray's Advanced 3 piece drain offers plenty of flexibility and safety as well. The integrated plastic channel is factory installed into the tray assuring a water tight seal and allowing for the waste trap to be connected anywhere along the channel. The 304 grade stainless steel frame and cover make up the remaining parts of the drain. They are available in a variety of PVD coated colours and finishes. The frame is height adjustable to match the finished floor height. It also offers secondary drainage in case water were to ever penetrate the floor covering it will find its way to the drain. The cover itself is reversible, allowing you to either leave it right side up for a stainless steel finish to the cover or flipping it over and tiling inside for a tiled finish.

These XPS foam Trays have a 4 way slope machine cut into with an estimated 1-2% gradient fall. The bottom side of the tray is level and the integrated channel does not protrude below the tray allowing for both timber and concrete floor installation. Furthermore the hole (hole cutter provided) for the waste trap is drilled on site by the installer making avoiding joists that much simpler. Although the tray provides great thermal and acoustic insulation it is not structural so it will require to be supported throughout its entirety. The Trays are trim-able and can be cut down to a specific size or to avoid corners or match uneven walls or irregular angles.

This longer but narrow tray is a great option for a small shower with a comfortable entrance. The drain is located 150mm from the short end  while the far end of the tray still has a sloped floor. Our Wet Room Shower Trays with Linear drains for tiled floors are the most versatile shower former you will find. They come with an integrated 600mm linear drain and are available in various sizes with different drain positions.

Each Tray's Advanced 3 piece drain offers plenty of flexibility and safety as well. The integrated plastic channel is factory installed into the tray assuring a water tight seal and allowing for the waste trap to be connected anywhere along the channel. The 304 grade stainless steel frame and cover make up the remaining parts of the drain. They are available in a variety of PVD coated colours and finishes. The frame is height adjustable to match the finished floor height. It also offers secondary drainage in case water were to ever penetrate the floor covering it will find its way to the drain. The cover itself is reversible, allowing you to either leave it right side up for a stainless steel finish to the cover or flipping it over and tiling inside for a tiled finish.

These XPS foam Trays have a 4 way slope machine cut into with an estimated 1-2% gradient fall. The bottom side of the tray is level and the integrated channel does not protrude below the tray allowing for both timber and concrete floor installation. Furthermore the hole (hole cutter provided) for the waste trap is drilled on site by the installer making avoiding joists that much simpler. Although the tray provides great thermal and acoustic insulation it is not structural so it will require to be supported throughout its entirety. The Trays are trim-able and can be cut down to a specific size or to avoid corners or match uneven walls or irregular angles.

Sightly large variant from our most popular size. Provides plenty of space for showering and allows extra space for the entrance. The drain channel is 60mm long and is 150mm away from the short side of the tray. Our Wet Room Shower Trays with Linear drains for tiled floors are the most versatile shower former you will find. They come with an integrated 600mm linear drain and are available in various sizes with different drain positions.

Each Tray's Advanced 3 piece drain offers plenty of flexibility and safety as well. The integrated plastic channel is factory installed into the tray assuring a water tight seal and allowing for the waste trap to be connected anywhere along the channel. The 304 grade stainless steel frame and cover make up the remaining parts of the drain. They are available in a variety of PVD coated colours and finishes. The frame is height adjustable to match the finished floor height. It also offers secondary drainage in case water were to ever penetrate the floor covering it will find its way to the drain. The cover itself is reversible, allowing you to either leave it right side up for a stainless steel finish to the cover or flipping it over and tiling inside for a tiled finish.

These XPS foam Trays have a 4 way slope machine cut into with an estimated 1-2% gradient fall. The bottom side of the tray is level and the integrated channel does not protrude below the tray allowing for both timber and concrete floor installation. Furthermore the hole (hole cutter provided) for the waste trap is drilled on site by the installer making avoiding joists that much simpler. Although the tray provides great thermal and acoustic insulation it is not structural so it will require to be supported throughout its entirety. The Trays are trim-able and can be cut down to a specific size or to avoid corners or match uneven walls or irregular angles.

Spacious tray with longer entrance option. This 1.6 metre long tray allows you to have a wide screen without sacrificing the entrance opening. The 600mm long linear drain is located 150mm from the short side of the tray and offers a gradual slope from all sides. Our Wet Room Shower Trays with Linear drains for tiled floors are the most versatile shower former you will find. They come with an integrated 600mm linear drain and are available in various sizes with different drain positions.

Each Tray's Advanced 3 piece drain offers plenty of flexibility and safety as well. The integrated plastic channel is factory installed into the tray assuring a water tight seal and allowing for the waste trap to be connected anywhere along the channel. The 304 grade stainless steel frame and cover make up the remaining parts of the drain. They are available in a variety of PVD coated colours and finishes. The frame is height adjustable to match the finished floor height. It also offers secondary drainage in case water were to ever penetrate the floor covering it will find its way to the drain. The cover itself is reversible, allowing you to either leave it right side up for a stainless steel finish to the cover or flipping it over and tiling inside for a tiled finish.

These XPS foam Trays have a 4 way slope machine cut into with an estimated 1-2% gradient fall. The bottom side of the tray is level and the integrated channel does not protrude below the tray allowing for both timber and concrete floor installation. Furthermore the hole (hole cutter provided) for the waste trap is drilled on site by the installer making avoiding joists that much simpler. Although the tray provides great thermal and acoustic insulation it is not structural so it will require to be supported throughout its entirety. The Trays are trim-able and can be cut down to a specific size or to avoid corners or match uneven walls or irregular angles.

This tray is a great option for covering a large area of the room with a sloped floor. This will ensure that the room does not have any standing water left after it's been used. The 600mm drain at the end of the tray will collect all the water and drain it away. Our Wet Room Shower Trays with Linear drains for tiled floors are the most versatile shower former you will find. They come with an integrated 600mm linear drain and are available in various sizes with different drain positions.

Each Tray's Advanced 3 piece drain offers plenty of flexibility and safety as well. The integrated plastic channel is factory installed into the tray assuring a water tight seal and allowing for the waste trap to be connected anywhere along the channel. The 304 grade stainless steel frame and cover make up the remaining parts of the drain. They are available in a variety of PVD coated colours and finishes. The frame is height adjustable to match the finished floor height. It also offers secondary drainage in case water were to ever penetrate the floor covering it will find its way to the drain. The cover itself is reversible, allowing you to either leave it right side up for a stainless steel finish to the cover or flipping it over and tiling inside for a tiled finish.

These XPS foam Trays have a 4 way slope machine cut into with an estimated 1-2% gradient fall. The bottom side of the tray is level and the integrated channel does not protrude below the tray allowing for both timber and concrete floor installation. Furthermore the hole (hole cutter provided) for the waste trap is drilled on site by the installer making avoiding joists that much simpler. Although the tray provides great thermal and acoustic insulation it is not structural so it will require to be supported throughout its entirety. The Trays are trim-able and can be cut down to a specific size or to avoid corners or match uneven walls or irregular angles.

The longest tray in our series. This tray is twice as long as it is wide and is a great option when considering having the entire floor of a small wet room contain a slope toward the drain. The tray's slope is very gradual however it's sufficient enough that the water from the entire tray will find its way to the drain. Our Wet Room Shower Trays with Linear drains for tiled floors are the most versatile shower former you will find. They come with an integrated 600mm linear drain and are available in various sizes with different drain positions.

Each Tray's Advanced 3 piece drain offers plenty of flexibility and safety as well. The integrated plastic channel is factory installed into the tray assuring a water tight seal and allowing for the waste trap to be connected anywhere along the channel. The 304 grade stainless steel frame and cover make up the remaining parts of the drain. They are available in a variety of PVD coated colours and finishes. The frame is height adjustable to match the finished floor height. It also offers secondary drainage in case water were to ever penetrate the floor covering it will find its way to the drain. The cover itself is reversible, allowing you to either leave it right side up for a stainless steel finish to the cover or flipping it over and tiling inside for a tiled finish.

These XPS foam Trays have a 4 way slope machine cut into with an estimated 1-2% gradient fall. The bottom side of the tray is level and the integrated channel does not protrude below the tray allowing for both timber and concrete floor installation. Furthermore the hole (hole cutter provided) for the waste trap is drilled on site by the installer making avoiding joists that much simpler. Although the tray provides great thermal and acoustic insulation it is not structural so it will require to be supported throughout its entirety. The Trays are trim-able and can be cut down to a specific size or to avoid corners or match uneven walls or irregular angles.