On sale

Our most popular size tray, but this one offers the drain along the 1600mm side of the tray. The drain is 600mm long and is located 150mm from the edge. This is a great option for a shower that is wider than it is longer. Our Wet Room Shower Trays with Linear drains for tiled floors are the most versatile shower former you will find. They come with an integrated 600mm linear drain and are available in various sizes with different drain positions.

Each Tray's Advanced 3 piece drain offers plenty of flexibility and safety as well. The integrated plastic channel is factory installed into the tray assuring a water tight seal and allowing for the waste trap to be connected anywhere along the channel. The 304 grade stainless steel frame and cover make up the remaining parts of the drain. They are available in a variety of PVD coated colours and finishes. The frame is height adjustable to match the finished floor height. It also offers secondary drainage in case water were to ever penetrate the floor covering it will find its way to the drain. The cover itself is reversible, allowing you to either leave it right side up for a stainless steel finish to the cover or flipping it over and tiling inside for a tiled finish.

These XPS foam Trays have a 4 way slope machine cut into with an estimated 1-2% gradient fall. The bottom side of the tray is level and the integrated channel does not protrude below the tray allowing for both timber and concrete floor installation. Furthermore the hole (hole cutter provided) for the waste trap is drilled on site by the installer making avoiding joists that much simpler. Although the tray provides great thermal and acoustic insulation it is not structural so it will require to be supported throughout its entirety. The Trays are trim-able and can be cut down to a specific size or to avoid corners or match uneven walls or irregular angles.

Our most popular size tray, but this one offers the drain along the 1700mm side of the tray. The drain is 600mm long and is located 150mm from the edge. This is a great option for a shower that is wider than it is longer. Our Wet Room Shower Trays with Linear drains for tiled floors are the most versatile shower former you will find. They come with an integrated 600mm linear drain and are available in various sizes with different drain positions.

Each Tray's Advanced 3 piece drain offers plenty of flexibility and safety as well. The integrated plastic channel is factory installed into the tray assuring a water tight seal and allowing for the waste trap to be connected anywhere along the channel. The 304 grade stainless steel frame and cover make up the remaining parts of the drain. They are available in a variety of PVD coated colours and finishes. The frame is height adjustable to match the finished floor height. It also offers secondary drainage in case water were to ever penetrate the floor covering it will find its way to the drain. The cover itself is reversible, allowing you to either leave it right side up for a stainless steel finish to the cover or flipping it over and tiling inside for a tiled finish.

These XPS foam Trays have a 4 way slope machine cut into with an estimated 1-2% gradient fall. The bottom side of the tray is level and the integrated channel does not protrude below the tray allowing for both timber and concrete floor installation. Furthermore the hole (hole cutter provided) for the waste trap is drilled on site by the installer making avoiding joists that much simpler. Although the tray provides great thermal and acoustic insulation it is not structural so it will require to be supported throughout its entirety. The Trays are trim-able and can be cut down to a specific size or to avoid corners or match uneven walls or irregular angles.

Our most popular size tray, but this one offers the drain along the 1850mm side of the tray. The drain is 600mm long and is located 150mm from the edge. This is a great option for a shower that is wider than it is longer. Our Wet Room Shower Trays with Linear drains for tiled floors are the most versatile shower former you will find. They come with an integrated 600mm linear drain and are available in various sizes with different drain positions.

Each Tray's Advanced 3 piece drain offers plenty of flexibility and safety as well. The integrated plastic channel is factory installed into the tray assuring a water tight seal and allowing for the waste trap to be connected anywhere along the channel. The 304 grade stainless steel frame and cover make up the remaining parts of the drain. They are available in a variety of PVD coated colours and finishes. The frame is height adjustable to match the finished floor height. It also offers secondary drainage in case water were to ever penetrate the floor covering it will find its way to the drain. The cover itself is reversible, allowing you to either leave it right side up for a stainless steel finish to the cover or flipping it over and tiling inside for a tiled finish.

These XPS foam Trays have a 4 way slope machine cut into with an estimated 1-2% gradient fall. The bottom side of the tray is level and the integrated channel does not protrude below the tray allowing for both timber and concrete floor installation. Furthermore the hole (hole cutter provided) for the waste trap is drilled on site by the installer making avoiding joists that much simpler. Although the tray provides great thermal and acoustic insulation it is not structural so it will require to be supported throughout its entirety. The Trays are trim-able and can be cut down to a specific size or to avoid corners or match uneven walls or irregular angles.

The 800 mm x 1200 mm shower base is 20 mm thick and is designed to be tiled over, providing level access into the shower without a step up. The shower base is produced from XPS foam and re-enforced on both sides with a fibreglass mesh and coated with a flexible cement. This surface is ready to tile onto. It's lightweight and flexible enough to absorb movement within the structural floor.

The shower base has a machined slope cut into it, providing a 4 way fall from each corner to the drain. The drain is offset from the centre of the tray, creating a shower zone to one end of the tray. While leaving the other end is more of a walkway or entrance to the shower. This allows for the entrance to still have a gradual slope for water to flow back toward the drain.

The XPS foam has great acoustic properties and therefore is an excellent choice for showers here in the UK, when you can generally hear everything that's going on upstairs! It can be easily trimmed if necessary, say around pipes or other obstacles, or if you are fitting a shower that is not quite the size of the tray. The height of the drain is 10mm, however this can be extended to 17mm using the extension provided.

The 800 mm x 1200 mm shower base is 30 mm thick and is designed to be tiled over, providing level access into the shower without a step up. The shower base is produced from XPS foam and re-enforced on both sides with a fibreglass mesh and coated with a flexible cement. This surface is ready to tile onto. It's lightweight and flexible enough to absorb movement within the structural floor.

The XPS foam has great acoustic properties and therefore is an excellent choice for showers here in the UK, when you can generally hear everything that's going on upstairs! It can be easily trimmed if necessary, say around pipes or other obstacles, or if you are fitting a shower that is not quite the size of the tray.

The shower base has a machined slope cut into it, providing a 4 way fall from each corner to the drain. The enveloped shaped pattern helps guide the water toward the channel, eliminating the need to create fall on your own.

The 800 mm x 1500 mm shower base is 20 mm thick and is designed to be tiled over, providing level access into the shower without a step up. The shower base is produced from XPS foam and re-enforced on both sides with a fibreglass mesh and coated with a flexible cement. This surface is ready to tile onto. It's lightweight and flexible enough to absorb movement within the structural floor.

The shower base has a machined slope cut into it, providing a 4 way fall from each corner to the drain. The drain is offset from the centre of the tray, creating a shower zone to one end of the tray. While leaving the other end is more of a walkway or entrance to the shower. This allows for the entrance to still have a gradual slope for water to flow back toward the drain.

The XPS foam has great acoustic properties and therefore is an excellent choice for showers here in the UK, when you can generally hear everything that's going on upstairs! It can be easily trimmed if necessary, say around pipes or other obstacles, or if you are fitting a shower that is not quite the size of the tray. The height of the drain is 10mm, however this can be extended to 17mm using the extension provided.

The 800 mm x 1500 mm shower base is 30 mm thick and is designed to be tiled over, providing level access into the shower without a step up. The shower base is produced from XPS foam and re-enforced on both sides with a fibreglass mesh and coated with a flexible cement. This surface is ready to tile onto. It's lightweight and flexible enough to absorb movement within the structural floor.

The XPS foam has great acoustic properties and therefore is an excellent choice for showers here in the UK, when you can generally hear everything that's going on upstairs! It can be easily trimmed if necessary, say around pipes or other obstacles, or if you are fitting a shower that is not quite the size of the tray.

The shower base has a machined slope cut into it, providing a 4 way fall from each corner to the drain. The enveloped shaped pattern helps guide the water toward the channel, eliminating the need to create fall on your own.

The 800 mm x 1800 mm shower base is 26 mm thick and is designed to be tiled over, providing level access into the shower without a step up. The shower base is produced from XPS foam and re-enforced on both sides with a fibreglass mesh and coated with a flexible cement. This surface is ready to tile onto. It's lightweight and flexible enough to absorb movement within the structural floor.

The shower base has a machined slope cut into it, providing a 4 way fall from each corner to the drain. The drain is offset from the centre of the tray, creating a shower zone to one end of the tray. While leaving the other end is more of a walkway or entrance to the shower. This allows for the entrance to still have a gradual slope for water to flow back toward the drain.

The XPS foam has great acoustic properties and therefore is an excellent choice for showers here in the UK, when you can generally hear everything that's going on upstairs! It can be easily trimmed if necessary, say around pipes or other obstacles, or if you are fitting a shower that is not quite the size of the tray. The height of the drain is 10mm, however this can be extended to 17mm using the extension provided.

The 800 mm x 800 mm shower base is 20 mm thick and is designed to be tiled over, providing level access into the shower without a step up. The shower base is produced from XPS foam and re-enforced on both sides with a fibreglass mesh and coated with a flexible cement. This surface is ready to tile onto. It's lightweight and flexible enough to absorb movement within the structural floor.

The shower base has a machined slope cut into it, providing a 4 way fall from each corner to the drain. The XPS foam has great acoustic properties and therefore is an excellent choice for showers here in the UK, when you can generally hear everything that's going on upstairs!

It can be easily trimmed if necessary, say around pipes or other obstacles, or if you are fitting a shower really small space. The height of the drain is 10mm, however this can be extended to 17mm using the extension provided.

The 800 mm x 800 mm shower base is 30 mm thick and is designed to be tiled over, providing level access into the shower without a step up. The shower base is produced from XPS foam and re-enforced on both sides with a fibreglass mesh and coated with a flexible cement. This surface is ready to tile onto. It's lightweight and flexible enough to absorb movement within the structural floor.

The XPS foam has great acoustic properties and therefore is an excellent choice for showers here in the UK, when you can generally hear everything that's going on upstairs! It can be easily trimmed if necessary, say around pipes or other obstacles, or if you are fitting a shower that is not quite the size of the tray.

The shower base has a machined slope cut into it, providing a 4 way fall from each corner to the drain. The enveloped shaped pattern helps guide the water toward the channel, eliminating the need to create fall on your own.

The 900 mm x 1200 mm shower base is 20 mm thick and is designed to be tiled over, providing level access into the shower without a step up. The shower base is produced from XPS foam and re-enforced on both sides with a fibreglass mesh and coated with a flexible cement. This surface is ready to tile onto. It's lightweight and flexible enough to absorb movement within the structural floor.

The shower base has a machined slope cut into it, providing a 4 way fall from each corner to the drain. The XPS foam has great acoustic properties and therefore is an excellent choice for showers here in the UK, when you can generally hear everything that's going on upstairs!

It can be easily trimmed if necessary, say around pipes or other obstacles, or if you are fitting a shower that is not quite the size of the tray. The height of the drain is 10mm, however this can be extended to 17mm using the extension provided.

The 900 mm x 1200 mm shower base is 20 mm thick and is designed to be tiled over, providing level access into the shower without a step up. The shower base is produced from XPS foam and re-enforced on both sides with a fibreglass mesh and coated with a flexible cement. This surface is ready to tile onto. It's lightweight and flexible enough to absorb movement within the structural floor.

The shower base has a machined slope cut into it, providing a 4 way fall from each corner to the drain. The XPS foam has great acoustic properties and therefore is an excellent choice for showers here in the UK, when you can generally hear everything that's going on upstairs!

It can be easily trimmed if necessary, say around pipes or other obstacles, or if you are fitting a shower that is not quite the size of the tray. The height of the drain is 10mm, however this can be extended to 17mm using the extension provided

The 900 mm x 1200 mm shower base is 20 mm thick and is designed to be tiled over, providing level access into the shower without a step up. The shower base is produced from XPS foam and re-enforced on both sides with a fibreglass mesh and coated with a flexible cement. This surface is ready to tile onto. It's lightweight and flexible enough to absorb movement within the structural floor.

The shower base has a machined slope cut into it, providing a 4 way fall from each corner to the drain. The drain is offset from the centre of the tray, creating a shower zone to one end of the tray. While leaving the other end is more of a walkway or entrance to the shower. This allows for the entrance to still have a gradual slope for water to flow back toward the drain.

The XPS foam has great acoustic properties and therefore is an excellent choice for showers here in the UK, when you can generally hear everything that's going on upstairs! It can be easily trimmed if necessary, say around pipes or other obstacles, or if you are fitting a shower that is not quite the size of the tray. The height of the drain is 10mm, however this can be extended to 17mm using the extension provided.

The 900 mm x 1200 mm shower base is 30 mm thick and is designed to be tiled over, providing level access into the shower without a step up. The shower base is produced from XPS foam and re-enforced on both sides with a fibreglass mesh and coated with a flexible cement. This surface is ready to tile onto. It's lightweight and flexible enough to absorb movement within the structural floor.

The XPS foam has great acoustic properties and therefore is an excellent choice for showers here in the UK, when you can generally hear everything that's going on upstairs! It can be easily trimmed if necessary, say around pipes or other obstacles, or if you are fitting a shower that is not quite the size of the tray.

The shower base has a machined slope cut into it, providing a 4 way fall from each corner to the drain. The enveloped shaped pattern helps guide the water toward the channel, eliminating the need to create fall on your own.

The 900 mm x 1400 mm shower base is 20 mm thick and is designed to be tiled over, providing level access into the shower without a step up. The shower base is produced from XPS foam and re-enforced on both sides with a fibreglass mesh and coated with a flexible cement. This surface is ready to tile onto. It's lightweight and flexible enough to absorb movement within the structural floor.

The shower base has a machined slope cut into it, providing a 4 way fall from each corner to the drain. The drain is offset from the centre of the tray, creating a shower zone to one end of the tray. While leaving the other end is more of a walkway or entrance to the shower. This allows for the entrance to still have a gradual slope for water to flow back toward the drain.

The XPS foam has great acoustic properties and therefore is an excellent choice for showers here in the UK, when you can generally hear everything that's going on upstairs! It can be easily trimmed if necessary, say around pipes or other obstacles, or if you are fitting a shower that is not quite the size of the tray. The height of the drain is 10mm, however this can be extended to 17mm using the extension provided.

The 900 mm x 1400 mm shower base is 30 mm thick and is designed to be tiled over, providing level access into the shower without a step up. The shower base is produced from XPS foam and re-enforced on both sides with a fibreglass mesh and coated with a flexible cement. This surface is ready to tile onto. It's lightweight and flexible enough to absorb movement within the structural floor.

The XPS foam has great acoustic properties and therefore is an excellent choice for showers here in the UK, when you can generally hear everything that's going on upstairs! It can be easily trimmed if necessary, say around pipes or other obstacles, or if you are fitting a shower that is not quite the size of the tray.

The shower base has a machined slope cut into it, providing a 4 way fall from each corner to the drain. The enveloped shaped pattern helps guide the water toward the channel, eliminating the need to create fall on your own.

The 900 mm x 1500 mm shower base is 20 mm thick and is designed to be tiled over, providing level access into the shower without a step up. The shower base is produced from XPS foam and re-enforced on both sides with a fibreglass mesh and coated with a flexible cement. This surface is ready to tile onto. It's lightweight and flexible enough to absorb movement within the structural floor.

The shower base has a machined slope cut into it, providing a 4 way fall from each corner to the drain. The drain is offset from the centre of the tray, creating a shower zone to one end of the tray. While leaving the other end is more of a walkway or entrance to the shower. This allows for the entrance to still have a gradual slope for water to flow back toward the drain.

The XPS foam has great acoustic properties and therefore is an excellent choice for showers here in the UK, when you can generally hear everything that's going on upstairs! It can be easily trimmed if necessary, say around pipes or other obstacles, or if you are fitting a shower that is not quite the size of the tray. The height of the drain is 10mm, however this can be extended to 17mm using the extension provided.

The 900 mm x 1500 mm shower base is 30 mm thick and is designed to be tiled over, providing level access into the shower without a step up. The shower base is produced from XPS foam and re-enforced on both sides with a fibreglass mesh and coated with a flexible cement. This surface is ready to tile onto. It's lightweight and flexible enough to absorb movement within the structural floor.

The XPS foam has great acoustic properties and therefore is an excellent choice for showers here in the UK, when you can generally hear everything that's going on upstairs! It can be easily trimmed if necessary, say around pipes or other obstacles, or if you are fitting a shower that is not quite the size of the tray.

The shower base has a machined slope cut into it, providing a 4 way fall from each corner to the drain. The enveloped shaped pattern helps guide the water toward the channel, eliminating the need to create fall on your own.

The 900 mm x 1600 mm shower base is 20 mm thick and is designed to be tiled over, providing level access into the shower without a step up. The shower base is produced from XPS foam and re-enforced on both sides with a fibreglass mesh and coated with a flexible cement. This surface is ready to tile onto. It's lightweight and flexible enough to absorb movement within the structural floor.

The shower base has a machined slope cut into it, providing a 4 way fall from each corner to the drain. The drain is offset from the centre of the tray, creating a shower zone to one end of the tray. While leaving the other end is more of a walkway or entrance to the shower. This allows for the entrance to still have a gradual slope for water to flow back toward the drain.

The XPS foam has great acoustic properties and therefore is an excellent choice for showers here in the UK, when you can generally hear everything that's going on upstairs! It can be easily trimmed if necessary, say around pipes or other obstacles, or if you are fitting a shower that is not quite the size of the tray. The height of the drain is 10mm, however this can be extended to 17mm using the extension provided.

The 900 mm x 1600 mm shower base is 30 mm thick and is designed to be tiled over, providing level access into the shower without a step up. The shower base is produced from XPS foam and re-enforced on both sides with a fibreglass mesh and coated with a flexible cement. This surface is ready to tile onto. It's lightweight and flexible enough to absorb movement within the structural floor.

The XPS foam has great acoustic properties and therefore is an excellent choice for showers here in the UK, when you can generally hear everything that's going on upstairs! It can be easily trimmed if necessary, say around pipes or other obstacles, or if you are fitting a shower that is not quite the size of the tray.

The shower base has a machined slope cut into it, providing a 4 way fall from each corner to the drain. The enveloped shaped pattern helps guide the water toward the channel, eliminating the need to create fall on your own.

The 900 mm x 1700 mm shower base is 20 mm thick and is designed to be tiled over, providing level access into the shower without a step up. The shower base is produced from XPS foam and re-enforced on both sides with a fibreglass mesh and coated with a flexible cement. This surface is ready to tile onto. It's lightweight and flexible enough to absorb movement within the structural floor.

The shower base has a machined slope cut into it, providing a 4 way fall from each corner to the drain. The drain is offset from the centre of the tray, creating a shower zone to one end of the tray. While leaving the other end is more of a walkway or entrance to the shower. This allows for the entrance to still have a gradual slope for water to flow back toward the drain.

The XPS foam has great acoustic properties and therefore is an excellent choice for showers here in the UK, when you can generally hear everything that's going on upstairs! It can be easily trimmed if necessary, say around pipes or other obstacles, or if you are fitting a shower that is not quite the size of the tray. The height of the drain is 10mm, however this can be extended to 17mm using the extension provided.

The 900 mm x 1700 mm shower base is 30 mm thick and is designed to be tiled over, providing level access into the shower without a step up. The shower base is produced from XPS foam and re-enforced on both sides with a fibreglass mesh and coated with a flexible cement. This surface is ready to tile onto. It's lightweight and flexible enough to absorb movement within the structural floor.

The XPS foam has great acoustic properties and therefore is an excellent choice for showers here in the UK, when you can generally hear everything that's going on upstairs! It can be easily trimmed if necessary, say around pipes or other obstacles, or if you are fitting a shower that is not quite the size of the tray.

The shower base has a machined slope cut into it, providing a 4 way fall from each corner to the drain. The enveloped shaped pattern helps guide the water toward the channel, eliminating the need to create fall on your own.

The 900 mm x 1850 mm shower base is 20 mm thick and is designed to be tiled over, providing level access into the shower without a step up. The shower base is produced from XPS foam and re-enforced on both sides with a fibreglass mesh and coated with a flexible cement. This surface is ready to tile onto. It's lightweight and flexible enough to absorb movement within the structural floor.

The shower base has a machined slope cut into it, providing a 4 way fall from each corner to the drain. The drain is offset from the centre of the tray, creating a shower zone to one end of the tray. While leaving the other end is more of a walkway or entrance to the shower. This allows for the entrance to still have a gradual slope for water to flow back toward the drain.

The XPS foam has great acoustic properties and therefore is an excellent choice for showers here in the UK, when you can generally hear everything that's going on upstairs! It can be easily trimmed if necessary, say around pipes or other obstacles, or if you are fitting a shower that is not quite the size of the tray. The height of the drain is 10mm, however this can be extended to 17mm using the extension provided.

The 900 mm x 1850 mm shower base is 30 mm thick and is designed to be tiled over, providing level access into the shower without a step up. The shower base is produced from XPS foam and re-enforced on both sides with a fibreglass mesh and coated with a flexible cement. This surface is ready to tile onto. It's lightweight and flexible enough to absorb movement within the structural floor.

The XPS foam has great acoustic properties and therefore is an excellent choice for showers here in the UK, when you can generally hear everything that's going on upstairs! It can be easily trimmed if necessary, say around pipes or other obstacles, or if you are fitting a shower that is not quite the size of the tray.

The shower base has a machined slope cut into it, providing a 4 way fall from each corner to the drain. The enveloped shaped pattern helps guide the water toward the channel, eliminating the need to create fall on your own.